Quick Question!

Have you ever purchased from PartSelect.com before?

11738914-1-S-Whirlpool-WP2155013-Bottom Kickplate Clip
11738914-1-S-Whirlpool-WP2155013-Bottom Kickplate Clip 11738914-2-S-Whirlpool-WP2155013-Bottom Kickplate Clip 11738914-3-S-Whirlpool-WP2155013-Bottom Kickplate Clip https://www.partselect.com/Schematics/Maytag/6FZLLLTT.gif

Bottom Kickplate Clip

Your Price

$4.88
Order within the next 12 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11738914
Manufacturer Part Number WP2155013
Manufactured by Whirlpool

This clip is sold individually.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Estate, Crosley, Maytag, Inglis, Amana.

This part works with the following products: Refrigerator, Range.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Recent

Question:

Is there just a clip for the kickplate grill on the left side of the fridge. As per your diagram it only shows #6 on the left. The bottom right side of my grill drags on the floor and has nothing to attach to. Previous owner may have broken it off if it did exist.

Margo for model number GS2KVAXVS01
Answer:

Hi Margo, Thank you for your inquiry. You would be able to use the clip on both sides. I hope this helps. Thank you and have a great day!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 3 reviews What's this?
1-3 of 3
 

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Randall from Perry, IA

Unit stopped making ice

First, I loosened the two top screws and removed
the bottom screw. Then lifted the unit up and out.
Next, I unplugged the wire plug and removed the
ice maker unit from frig. The replacement ice maker was identical to the original, wire loom and all. So all I had to do is plug in the wire plug, slide the top down on the loosened screws and tighten them. Next, installed the bottom screw, turned on the water,flipped the wire down and waited for ice. We had ice being made by the next morning and in about 3 days had a full bin.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Joseph from University Place, WA

Replaced broken/missing parts

poped in, replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Bottom Kickplate Clip
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Gregory from Virginia Beach, VA

Dryer made loud intermittant humming sound after 20-30 minutes of use

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11738914
Manufacturer Part Number: WP2155013
Brand Model Number Description
Kenmore10640212010Refrigerator
Kenmore10640262010Refrigerator
Kenmore10640263010Refrigerator
Kenmore10640269010Refrigerator
Kenmore10640562010Refrigerator
Kenmore10640563010Refrigerator
Kenmore10640563011Refrigerator
Kenmore10640569010Refrigerator
Kenmore10640569011Refrigerator
Kenmore10641012100Refrigerator
Kenmore10641012101Refrigerator
Kenmore10641012104Refrigerator
Kenmore10641014100Refrigerator
Kenmore10641014101Refrigerator
Kenmore10641014104Refrigerator
Kenmore10641212100Refrigerator
Kenmore10641212101Refrigerator
Kenmore10641214100Refrigerator
Kenmore10641214101Refrigerator
Kenmore10641262800Refrigerator
Kenmore10641262801Refrigerator
Kenmore10641263800Refrigerator
Kenmore10641263801Refrigerator
Kenmore10641263802Refrigerator
Kenmore10641264800Refrigerator
Kenmore10641264801Refrigerator
Kenmore10641269800Refrigerator
Kenmore10641269801Refrigerator
Kenmore10641512100Refrigerator
Kenmore10641512101Refrigerator