Maytag/Maytag_Thumb/37308.gif
See part 6 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Injector Tube

★★★★★
★★★★★
3 Reviews

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11738907
Manufacturer Part Number WP215235
Manufactured by Whirlpool
Product Description

Injector Tube Specifications

This injector tube is a little over two inches long. It it white and made of plastic.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Jenn-Air.
Part# WP215235 replaces these:
215235
Questions and Answers

Be the first to ask our experts a question about this part!

Customer Repair Stories
 Average Repair Rating: 3.4 / 5.0, 3 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Agitator Not Woking
    Unplugged power cord then disconnected the water supply and drain hose. Removed 2 screws and took the front panel off. Laid washer on it's side and posistioned the transmission with the cover facing upward. Removed the hex head screws then used a razor knife and a putty knife to remove the silicone sealant. Found that the agitator shaft spring had broken and fallen into the housing jamming the gears that's used in agitation. Removed the oil and all broken pieces of the spring. Installed new shaft spring, replaced the oil then applied sealant to the cover and screwed the cover back down. Let the washer stay in the same posistion for about 18 hours to let sealant dry completely. Then I sat the washer back on it's feet and removed 2 screws that holds the top lid in place. This allowed me access to the tub cover where the injector t is located. Installed the injector t along with the injector tube seal. Connected the hose and hose clamp. Then I put the lid back down and secured with the screws. Connected the water supply and drain hose then the power and selected a wash time and observed the operation. Everything worked ok so I put the front cover back on. Note: I had used the injector t from this washer to fix another washer that an appliance dealer had given me to use for parts to repair the one just described above. That was the only thing that was wrong with it. It was used for about a year and a half and it developed a problem in the spin cycle. Appears to be a brake problem. I intend to repair it as well.
    Other Parts Used:
    Hose Clamp Agitator Shaft Spring Injector Tube Seal
    • Richard from Alexander City, AL
    • Difficulty Level:
      Easy
    • Total Repair Time:
      1- 2 hours
    • Tools:
      Nutdriver, Pliers, Screw drivers, Socket set
    18 of 21 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Tub injector hose had hole in it from rubbing on side of cabinet.
    Remove front panel of machine, 2 screws at
    bottom. Remove 2 bolts at top front with nut
    driver and whole top can be lifted to expose
    all parts. Remove injector hose clamps and
    clamp new hoses in place. I replaced both
    injejctor hoses while open although only one
    had small hole in it. This is the only repair
    done on this coin-op machine in 20 years. At
    this time I did replace both drive belts but they
    could have run for more years, no cracks or
    breaks in belts. This machine is in a 12 unit
    apartment building. We have two on them,
    same age. We purchased both coin ops new
    in 1987.
    Other Parts Used:
    Injector Fill Hose Injector Tube Seal Injector Hose
    • Linn from El Segundo, CA
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Nutdriver, Screw drivers
    4 of 6 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Hot water overflow injector, ran onto floor
    You will need 2 hose clamps not sold as maytag parts.

    Remove front washer panel screws.

    Remove bolts holding front of top to side panels

    Remove hose clamp from front hose to injector sleeve.

    Twist fill hose ccw 90 degrees at tub fitting to remove.

    Clean corrosion at tub attachment point wuth wire brush.

    Paint bare metal to seal. Allow to thoroughly dry.

    Remove injector sleeve and injector hose.

    Trim new injector hose to match length of removed hose (I cut off abt 4 inches)

    Install injector hose and plastic sleeve. Ensure clocking is correct on hose.

    Install gasket on fill hose fitting.

    Insert fitting into tub. Rotate 90 deg CW to latch.

    Install gear clamps loosely on fill tube.

    Attach fill tube to fill fitting and injector sleeve.

    Slide clamps onto tube ends ensuring clamp clocking provides access and clears tub top..

    Test tub fill to ensure injector works without leaks
    Other Parts Used:
    Injector Fill Hose Rubber Injector Valve Injector Sleeve Injector Tube Seal Plastic Injector Nozzle Injector Hose
    • Padraic from SAINT PAUL, MN
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Screw drivers, Socket set
    2 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      3 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        3
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11738907
          Manufacturer Part Number: WP215235
          Brand
          Model Number
          Description
          Maytag
          A104
          Washer - Top Loading
          Maytag
          A105
          Washer - Top Loading
          Maytag
          A112
          Washer - Top Loading
          Maytag
          A183
          Washer - Top Loading
          Maytag
          A190
          Washer - Top Loading
          Maytag
          A1910
          Washer - Top Loading
          Maytag
          A211
          Washer - Top Loading
          Maytag
          A211S
          Washer - Top Loading
          Maytag
          A212
          Washer - Top Loading
          Maytag
          A212S
          Washer - Residential
          Maytag
          A23CA
          Washer
          Maytag
          A23CDL
          Washer - Commercial
          Maytag
          A23CDW
          Washer - Commercial
          Maytag
          A23CSL
          Washer
          Maytag
          A23CSW
          Washer
          Maytag
          A23CT
          Washer
          Maytag
          A24CA
          Washer
          Maytag
          A25CA
          Washer
          Maytag
          A25CAE
          Washer
          Maytag
          A25CM
          Washer
          Maytag
          A25CME
          Washer
          Maytag
          A25CS
          Washer
          Maytag
          A25CT
          Washer
          Maytag
          A26CA
          Washer
          Maytag
          A26CAE
          Washer
          Maytag
          A26CD
          Washer
          Maytag
          A26CDC
          Washer
          Maytag
          A282
          Washer - Top Loading
          Maytag
          A283
          Washer - Top Loading
          Maytag
          A284
          Washer - Top Loading

          Get in touch, we're here to help!

          Open until 1am EST

          Contact Customer Service