Maytag/Maytag_Thumb/57962.gif
See part 4 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Ice Chute Seal

★★★★★
★★★★★
2 Reviews
$7.09   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11738577
Manufacturer Part Number WP12665101
Manufactured by Whirlpool
Troubleshooting
This part fixes the following symptoms:
Door Sweating
This part works with the following products:
Refrigerator.
This part works with the following products:
Amana, Maytag, Kenmore, Jenn-Air.
Part# WP12665101 replaces these:
AP6005528, 12563301, 12665101, 12665101SP
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 4.2 / 5.0, 9 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    ice build up in the dispenser chute
    removed the spill tray, then two bolts. removed ice dispenser assembly by removing 3 more bolts. changed the seal and the insulation and reimstalled unit in hte reverse order. works perfectly -no more ice build up in the chute.
    • Joe from Strongsville, OH
    • Difficulty Level:
      Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Socket set
    • Parts Used:
      WP67007098, WP12665101
    77 of 1254 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Significant frost forming on ice chute.
    Following diagram on website, I removed the 2 screws on the face of freezer door ice dispencer.Removed old chute door and solenoid. Replaced with new. I purchased all parts involved because they were inexpensive. The issue was most likely the solenoid.After installation ,the chute door had a sound of being positively closed by the solenoid.I\Frost no longer forming!
    47 of 712 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Water dispenser got stuck on one function, couldn't get water to work
    Removed two screws and took off water dispenser front panel. Unplugged wires to old control board and removed it from brackets holding it to inside of dispenser panel. Aligned and pushed new control (with care to only touch the outside edges of board...cannot touch circuitry which will permanently damage it). Was tricky aligning the board and snapping it back on, but finally got it in place. Repositioned dispenser panel and reattached two screws.
    Second problem was the Chute and chute seal had broken off from the hinge chute so it wouldn't open or close when dispensing ice. Was pretty tricky to realign the chute seal to the hinge, but with some paitence and manipulation, was able to reconnect them.
    I am REALLY impressed with the detailed drawings I found on PartSelect.com's website. Without these drawings it would have been difficult for me (my husband and son put the parts in, I did the ordering) to know what parts to order. Service was EXCELLENT. I would definitely do business with this company again. Great work!
    12 of 16 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Ice cube door not shutting
    Took the front panel off,replaced the parts inside on the door ,Replaced the panel ,Tested
    Now found out that it is the solniod that is bad ,Part on order ,Thanks
    8 of 15 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Ice maker door broke allowing open hole to freezer
    The ice maker panel on the freezer door detaches by removing two screens at the bottom of the panel behind the drip tray. My son held the panel while I removed three screws holding the ice chute cover. The ice chute door is attached to a spring loaded bracket. I only needed the actual door, but it was just as easy to replace the insulation and the seal. The seal was starting to show wear. I then replaced the ice chute cover and tested the ice maker. With everything working correctly, I reinstalled the panel in the door.
    7 of 10 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Icemaker chute door seal was deteriorated
    Watched a Utube video
    • David from DUNNELLON, FL
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      15 - 30 mins
    • Tools:
      Nutdriver, Screw drivers
    • Parts Used:
      WP12665101, WP12562701
    2 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    seal leaking
    pull open seal lift up release bottem catch push in to release top catch clean disk and installnew seal put back in the reverse of taking out dont take any thing else apart
    • john from TITUSVILLE, FL
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
    • Parts Used:
      WP12665101
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    The Ice Cube Door Clips Broke
    1 - Look at the schematic for the "Fountain" on Partselect.com
    2 -Order the ice chute door and seal (seal is rubber and eventually it will stop sealing - while you are in there go ahead and change it)
    3 - Unplug the refrigerator then remove the sump tray by pulling it straight out from the door
    4 - Unscrew the two screws hidden behind the sump tray - hold the dispenser front housing in place so it doesn't drop downward - after removing the two screws slide the dispenser front housing downward while pressing it against the refrigerator door - there are two clips on the back of the housing that hold it against the refrigerator door
    5 - Gently pull the dispenser front housing out of the refrigerator door an inch or two - you will be able to see the electrical connections between the dispenser front housing and the refrigerator.
    6 - Continue pulling out the dispenser front housing until you can reach the multi-wire connector on the left - the connector is held together by a clip on the bottom center - squeeze the clip at the end closest to the wires to release it - gently pull the connector off
    7 - In the center of the back of the dispenser front housing is a black plastic box (the limit switch) - again, gently pull it away from the two clips holing it on
    8 - Set the dispenser front housing aside
    9 - Slip the water hose out of the clips holding to to the chute
    10 - Unscrew the three screws holding the chute to the door (two on the left and one on the upper right - Slide the chute out of the door
    11 - Hold the door hinge so you don't accidentally break it (personal experience) and unclip the top then the bottom of the ice cube door from the hinge (the ice chute seal and ice chute door insulation are attached to the ice cube door - take all three out at the same time)
    12 - Slip the ice chute seal off of the ice cube door - pull the ice chute door insulation out of the ice cube door
    13 - Put the ice chute door insulation into the new ice chute door - Slip the ice chute seal onto the ice cube door (the schematic will give you the proper orientation for all of the parts)
    14 - Again holding the door hinge - slip the two "L" shaped clips onto the bottom of the ice chute door - rotate the ice chute door assembly and snap (gently) the two side clips into place over the opening in the door hinge
    15 - Breath a breath of relief if you didn't break anything
    16 - Slide the chute assembly over the white pin on the lower right of the refrigerator opening that accepts the chute
    17 - Replace the three screws that hold the chute assembly to the door - replace the water line
    18 - Clip the limit switch onto the back of the dispenser front housing
    19 - run the multi-wire connector behind the water line - connect it to the back of the dispenser front housing
    20 - Slip the wires back into the clips along the sides of the opening in the refrigerate door
    21 - Rest the dispenser front housing on the bottom of the door opening - it must fit flush to the door (top, bottom and sides) - Slide it gently upward until it stops - replace the two screws at the bottom rear of the dispenser front housing - slide the sump tray back in place
    22 - Plug in the refrigerator
    23 - Dispense ice cubes into a high ball glass and enjoy a job well done
    • Rocky from ALBANY, IN
    • Difficulty Level:
      Difficult
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Nutdriver, Screw drivers
    • Parts Used:
      WP12665101, WP12562701
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Frost and ice was building up on the top of the ice chute inside the freezer
    There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).
    • Harry from TUCSON, AZ
    • Difficulty Level:
      Very Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
    • Parts Used:
      WP12665101
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      2 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        2
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11738577
          Manufacturer Part Number: WP12665101
          Brand
          Model Number
          Description
          Kenmore
          59650002100
          Refrigerator
          Kenmore
          59650003100
          Refrigerator
          Kenmore
          59650004100
          Refrigerator
          Kenmore
          59650009100
          Refrigerator
          Kenmore
          59650012100
          Refrigerator
          Kenmore
          59650013100
          Refrigerator
          Kenmore
          59650014100
          Refrigerator
          Kenmore
          59650019100
          Refrigerator
          Kenmore
          59651672100
          Refrigerator
          Kenmore
          59651673100
          Refrigerator
          Kenmore
          59651674100
          Refrigerator
          Kenmore
          59651679100
          Refrigerator
          Kenmore
          59652672200
          Refrigerator
          Kenmore
          59652672201
          Refrigerator
          Kenmore
          59652672202
          Refrigerator
          Kenmore
          59652673200
          Refrigerator
          Kenmore
          59652673201
          Refrigerator
          Kenmore
          59652673202
          Refrigerator
          Kenmore
          59652674200
          Refrigerator
          Kenmore
          59652674201
          Refrigerator
          Kenmore
          59652674202
          Refrigerator
          Kenmore
          59652679200
          Refrigerator
          Kenmore
          59652679201
          Refrigerator
          Kenmore
          59652679202
          Refrigerator
          Kenmore
          59653462300
          Refrigerator
          Kenmore
          59653462301
          Refrigerator
          Kenmore
          59653462302
          Refrigerator
          Kenmore
          59653463300
          Refrigerator
          Kenmore
          59653463301
          Refrigerator
          Kenmore
          59653463302
          Refrigerator

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service