Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Andrew V - May 6, 2019
Verified Purchase
Wrong part- my fault!
Part was correct, I just ordered the wrong thing
★★★★★
★★★★★
Carlos G - August 3, 2018
Verified Purchase
worked as expected!
The only problem was that i recived only 1 spring and had ordered 2
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Ice/Water Dispenser Pedal not working consistently
1. Pull off the removable drip tray that covers the two screws. 2. Remove these octagon shaped screws with the appropriate tool. 3. Remove the cover. ( You can cover a screw driver with a thin cloth so as not to scratch the stainless steel and then slide it between the refrigerator and the cover.) 4. Remove the three connectors from
... Read more the circuit board. 5. Remove two more nuts holding the dispenser yoke paddle. IMPORTANT: Note how the spring is attached to the paddle.TIP: Take pictures as you remove it and a close up of the spring so as not to forget how it is attached. 6. Snap off the paddle and spring. NOTE: There is another spring attached to the ice dispenser cover. Do not disturb this spring. 7. Replace the paddle and spring making sure the spring is placed correctly in the slot. 8. Complete by reversing the steps above.
Following diagram on website, I removed the 2 screws on the face of freezer door ice dispencer.Removed old chute door and solenoid. Replaced with new. I purchased all parts involved because they were inexpensive. The issue was most likely the solenoid.After installation ,the chute door had a sound of being positively closed by the solenoi
... Read mored.I\Frost no longer forming!
Took the front panel off,replaced the parts inside on the door ,Replaced the panel ,Tested Now found out that it is the solniod that is bad ,Part on order ,Thanks
This repair was really easy. I first removed the water evaporator tray exposing 2 nuts and removed them with driver. Detach the dispenser faceplate and unplug the connections from the circuit board. Remove 2 more nuts holding the dispenser yoke paddle.
Remove the snap in paddle and replace with new part and spring. Complete
... Read more assembly in reverse order. 10 minutes to complete repair.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kirby
October 22, 2017
The water does not shut off completely when dispenser is used. Have to manually return pad to closed position but even then, water continues to come out for 2 seconds or so.
For model number MFI2269VEM10
Hi Kirby,
Thank you for your question. It could possibly be the electrical solenoid that is part of your chute, part number: PS11738676 (Black) or PS11738677 (White). You may also want to check your water inlet valve as well. It could be that part is sending up too much water or not shutting off right away. I hope that helps. Good luck with your repair.