Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
John S - March 14, 2020
Verified Purchase
Easy Repair
Gasket arrived very quickly, watched the video installation went as smoothly as could be.
★★★★★
★★★★★
James M - October 29, 2019
Verified Purchase
Terribe to install. Had to be glued.
I would not recommend this part to anyone.
★★★★★
★★★★★
Bill V - December 28, 2018
Verified Purchase
very easy to use ,part fit correctly
instruction video was extremely helpful with tips
★★★★★
★★★★★
Jeff H - August 14, 2018
Verified Purchase
Fast service
part arrived in excellent condition. Installed, easily, and fridge us back in business. Thank you!!
★★★★★
★★★★★
Michael G - June 8, 2018
Verified Purchase
Door Seal
The part was the one I requested. Although it has been installed I'm still having difficulty in getting the door to seal properly. This installation isn't as easy as described.
★★★★★
★★★★★
Edward F - May 24, 2018
Verified Purchase
Thank you
Perfect. Great service.
★★★★★
★★★★★
Joann M - April 14, 2018
Verified Purchase
Refrigerator Door Gasket for an Amana
Gasket is not the same size as the original. Gasket could have been a little thicker. It's seals. It'll work for now. Installation was fair.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.9 / 5.0, 16 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Having patience and plenty of time
The refrigerator never gave me any trouble. It's at least 25 years old. It runs like new now. The gasket can be softened, gently using a hairdryer. The key is to attach the gasket to the refrigerator and use a hairdryer, going back and forth the length of the gasket. Then, to stop using the hairdryer and with the hands pull (gently) on t
... Read morehe gasket, the length of the gasket straightening and making the gasket wider so it attaches to the refrigerator as it cools. Then look for gaps and places where air is escaping and repeat, until a good seal is achieved. This is so much better than buying new, and in 10 years buying new again with planned obsolescence.
Fridge was dripping water (condensation), gasket was clearly deteriorated
I did not remove the door from the fridge deciding to replace the gasket while the door was still attached. Next time I will follow their suggestion to remove the door and lay it down. I didn't realize that when you take the screws out (And there are A LOT of screws!) the whole panel comes off the door. It also took a long time to clean t
... Read morehe door and panel with years of dirt/mildew to deal with. I had a hard time trying to get the kinks out with a hair dryer, didn't seem to work. Putting the new one on and screwing it back in place was pretty easy (would have been easier if it was laying flat). There are a couple of places where the seal is not perfect because of the kinks, but not going to worry about that.
Read less
Kathy from NEWARK, DE
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door gasket old and starting to come apart
removed upper freezer door, then removed refrig door,laid door on 2 saw horses, removed screws holding old gasket on,removed old gasket, installed new gasket as instructed by the on-line video,used an electric hair dryer to soften up gasket and work out the kinks,remounted he doors and i was done. door is back to sealing properly. the on
... Read more-line video was very helpful
Read less
james from FRIENDSHIP, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace both door gasgets
did not remove the doors. did freezer first ,removed inner door planel install gasget on panel and reinstalled. the aloney problem i had was trying to resape the door gasget on the big door. which is still a little out of shape hopeing it will fall in line over time.
It was a complete mess and a failure. There were no in structions with the gaskets except warming them in water to streatch them. Nothing with a photo of what the gasket looks like as it is being installed or after installation. I am still not convinced they are the correct gaskets for the model. It was a total waste of time and $130.00 t
... Read moreo try to replace the gaskets. In the end, I determined that it would be cheaper in the long run to buy a used refrigerator than to mess with the gaskets.
I hired a jack-of-all-trades friend of mine to do the job. He had just the right tool to take out all the screws so that went smoothly. Slipping the new gasket into place while I held the inner door shelving section in place was a little tricky and the gasket seemed a little off along the bottom and one side of the door frame. We gave it
... Read morea couple of days to seat itself. Two days later, there was condensation forming inside so my friend returned and took a look. He spotted a couple of places where the gasket magnet was not sealing properly. Out from his pocket, he pulled what looked like a brass jack knife with japanese writing on it and said it was a japanese carving tool. He opened up one of the parts that had a smooth blunt tip on it and slid it down the channel in the gasket from the outside. Voila! The magnet grabbed. He adjusted a couple of screws along the bottom and , after that, there were no more problems. So be sure to have your japanese carving toll ready when you start this job!
Read less
Sandra from Putney, VT
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad seal around the inside of refrigerator door
Loosened all the screws and pulled the old gasket off. It was fairly easy to get the new one in place. After I had it on it did not seal well so I had to use a hair dryer to get the seal tight.
James from St Charles, MN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Door Gasket
Emptied door shelves; removed umpteen screws (electric driver); replaced gasket and same umpteen screws; reloaded shelves. Didn't even turn off refrigerator. And, had great help from you (Sue) when I originally ordered the wrong gasket. Job was a piece of cake and your service outstanding.
John from Berkeley, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old seal was shot
New seal arrived basically folded in half for shipping. Was advised to use hair dryer and/or hot water to restore original shape. Neither worked. I installed it anyway and am waiting (3 days so far) for it to seal (so far, no luck). I'll give it another day or 2, re-install the old one and write off the $75
Steve from San Juan Capistrano, CA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The gasket size was perfect. Problem was it didn't seal the whole door properly, thus I'm getting evaporation.
I unscrewed about 20 screws from the door, took out the inside, cleaned it first, then put the door gasket on, Screwed the door back in place.
William from Fresh Meadows, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
LJ
May 28, 2019
I am having trouble finding a replacement door gasket for my Amana top mount's refrigerator door. I suspect that's because the original refrig. And freezer door gaskets are black and only white ones are available. I don't care about the gasket color — will this part fit my refrigerator (not the freezer) door?
For model number TX18VE — P1315706WE
Hello LJ, thank you for inquiring. Yes, this Refrigerator Door Gasket is compatible to your model.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
September 28, 2017
Have Amana refrig. # qt18r2w need door gasket. What one fits it? Thanks
For model number TQ18R2W
Hi Michael,
Thank you for your inquiry. The part number for correct refrigerator door gasket for your appliance is PS11738521. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kayleigh
March 20, 2023
My fridge door doesn't stay shut all the time. Would replacing the gasket around the door fix that problem?
For model number Tr18v1w
Hello Kayleigh, Thank you for your inquiry. We recommend replacing the Bottom Hinge Pin PS2070499.If you see gaps, or damage on your gasket, then it should be replaced. We are pleased to have been able to help.
I have an Amana refrigerator model #tx18vw in need of a door gasket. Will this one work?
For model number TX18VW
Hello Kurt, thank you for your question. Yes, the gasket Part Number: PS11738521 will work for your fridge door. Good luck with your repair!
Was this helpful?
Thank you for voting!
Michelle
June 10, 2019
Hi! Does this work with Amana ta181tw p1304501ww for the refrigerator door?Thank you tons.
For model number Amana ta181tw- p1304501ww
Hello Michelle, thank you for asking. Yes, this is the replacement for your model.
Was this helpful?
Thank you for voting!
Steven
July 25, 2019
Should the gasket have holes in ti?
For model number TQ18RTW
Hello Steven, Thank you for the question. The corners may have a small hole in the corners to let air out. Hope this helps!
Was this helpful?
Thank you for voting!
Ted
July 19, 2021
I am looking for the door seal for the refrigerator part of this refrigerator. Do you have that?
For model number TK18R3W
Hello Ted, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11738521. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
