Quick Question!

Have you ever purchased from PartSelect.com before?

11731755-1-S-Frigidaire-316490003-Oven Probe
11731755-1-S-Frigidaire-316490003-Oven Probe https://partselectcom.azureedge.net/Schematics/Frigidaire/MOHEIM5W.gif

Oven Probe

Your Price

$33.65
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11731755
Manufacturer Part Number 316490003
Manufactured by Frigidaire

The temperature sensor measures approximately 9 inches long. It sends the temperature up to the electronic control. Over time this can become weak and might be sending the wrong temperature signal. If you notice that your oven is not producing enough heat, it could be because the sensor has failed. This part is located at the back of the oven, and is held in place by a few screws and a wire harness. These will need to be removed. The sensor can be slid out from the hole. The new one simply slides into place.

This part works with the following brands: Frigidaire, Kenmore, Crosley, Electrolux, Tappan, Kelvinator, Westinghouse, Gibson.

This part works with the following products: Range, Wall Oven.

This part fixes the following symptoms:

  • Oven is too hot.
  • Little to no heat when baking.
  • Oven not heating evenly.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Why when the oven is turned on to preheat the element just goes to cherry red in a matter of seconds?

Mack for model number LGEF3033KWC
Answer:

Hi Mack, Thank you for the question, If the oven is getting to hot and not going to the proper temperature,I suggest replacing the PROBE,OVEN TEMP,Part Number: 316490003. If it is just with the pre heat mode that you are having issues and the oven heats normally during bake or broil model, I suggest checking into the Oven Control Board(clock/timer),Part Number: PS3490768. You can also try testing the probe if you have a Ohm meter. With the probe at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080–1090 ohms at room temperature. Hope this helps!

1 person found this helpful.
Question:

Baking and broiling does not heat up good. Top burners are working good. Control panel responds to settings selected. Would replacing the temp sensor be idea?

Walter for model number FGEF3055KBB
Answer:

Hello Walter, thank you for contacting us. It does sound like it would be the temperature sensor needing to be replaced. Good luck with the repair!

1 person found this helpful.
Question:

Oven not heating up; lower gas burner not igniting. Replaced ignitor and no effect. Oven functions when reset, by unplugging unit. Though, then after use fails to function again. Control board, temp probe or control unit next? What is the electrical draw on the temp probe?Thanks!

Adrian for model number FPGF3077QFB
Answer:

Hi Adrian, Thank you for the question. If the temp probe was defective you will still have heat in the oven but the temperature would not be consistent, so if you set the oven to 400 degrees the actual temperature would be well over 400 or it would not reach 400 but you would still have heat. I suggest replacing the Board PartSelect Number PS11700065. This is the Oven Relay board and controls the oven. Hope this helps!

1 person found this helpful.

Most Recent

Question:

Ordered, received and installed part #316490003 oven temp. Probe. Oven now heats up but extremely slow to reach temperature.This is the first use with new probe and it has taken 1 hour to reach 260 degrees. The quick heat setting beeps after a few minutes that it is hot but when you reset the oven immediately, using the regular bake button, it is still at 260 degrees.It is definitely heating, just slow.Is this just the new probe adjusting?

Susanne for model number LGEF3045KFC
Answer:

Hi Susanne, Thank you for the question. I suggest watching to see if the bottom bake element gets hot. Both elements work together to heat up and get to the set temperature. If the bottom element is not heating up the top element is doing all the work and will take a while to heat up. Hope this helps!

Question:

Have had the appliance for 8-10 years with no problem, but now neither the oven or broiler will heat up. You can set temp. And preheat and it goes through the program and beeps but the oven is only slightly warm and you can touch the broiler unit.

Susanne for model number LGEF3045KFC
Answer:

Hi Susanne, Thank you for the question. I suggest checking the Oven Temperature Probe for resistance with a Multi meter first. If the probe tests fine you may need to replace the Electronic Oven Control Board. Hope this helps!

Question:

No heat oven, have to replaced bake element . What next?

Loyd for model number FEF352ASA
Answer:

Hi Loyd, Thank you for the question. If you are not getting heat from the bake or broil elements I suggest replacing the Electronic Control Board,PartSelect Number PS977489. This board controls the oven. Hope this helps!

Question:

Error message f3. What does it mean?

Robin for model number FEFL77AQF
Answer:

Hi Robin, Thank you for your question. The F2 error code indicates that there is an issue with the oven sensor, electronic control board, or the wiring between both of the parts. I would suggest checking your oven sensor and the wiring first. If both of those parts are checking out fine, then it may be your control board that is the issue. Good luck with your repair.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 5 reviews What's this?
1-5 of 5
 

51 of 125 people found this instruction helpful

Parts Used:
  • Oven Probe
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: john from spring, TX

Oven temp not consistent with setting

took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
  • Oven Probe
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Michael J from STATEN ISLAND, NY

Trouble code f10 low oven temperature, oven not overheating,low resistance reading on ohm meter

Turned off electric,removed rear panel and replaced part.oven is now operating good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Oven Probe
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: George from TURNERSVILLE, NJ

Range would start beeping and needed to be unplugged.

Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Oven Probe
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Jess from DEWEY, OK

Oven would not heat up error code f10 showing on veiw screen

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 8 people found this instruction helpful

Parts Used:
  • Oven Probe
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Tim from ASHAWAY, RI

Oven did not heat up

Replaced the probe because that's what this site recommended.The oven still does not heat up.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11731755
Manufacturer Part Number: 316490003
Brand Model Number Description
Kenmore79071342700Range
Kenmore79071342701Range
Kenmore79071342702Range
Kenmore79071342703Range
Kenmore79071342704Range
Kenmore79071342705Range
Kenmore79071342706Range
Kenmore79071343700Range
Kenmore79071343701Range
Kenmore79071343703Range
Kenmore79071343704Range
Kenmore79071343705Range
Kenmore79071343706Range
Kenmore79071343707Range
Kenmore79071343708Range
Kenmore79071343709Range
Kenmore79071344700Range
Kenmore79071344701Range
Kenmore79071349700Range
Kenmore79071349701Range
Kenmore79071349702Range
Kenmore79071349703Range
Kenmore79071349704Range
Kenmore79071349705Range
Kenmore79071349706Range
Kenmore79071352700Range
Kenmore79071352701Range
Kenmore79071352702Range
Kenmore79071352703Range
Kenmore79071353700Range