Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gerald
August 11, 2017
Received my door seal.I did not receive either the instructions or the adhesive to mount the seal what do I use to bond the seal to the door. Where can I get it .
For model number MGDx655DW0
Hi Gerald,
Thank you for the questions. We recommenced the High Temperature Adhesive. Once you remove the old seal and clean any old glue from the channel the seal will fit into, you can squeeze the glue around the door into the channel and wait a min then line the seal with the glue and neatly press the seal down working around the door.
Hope this helps!
I purchased a door seal - part w10861521-- what adhesive does this require... please provide me a part number
For model number MEDC215EW0
Hello Wayne, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11757492. Thank you for your inquiry, good luck with this repair!
It takes 4 or 5 times to dry a regular load of clothes? Dryer heats but not enough to dry on 1st cycle
For model number MEDC200XW3
Hello Shawn, Thank you for the question. I suggest testing the Internal Bias Thermostat PartSelect Number PS11741405 and the thermostat and fuse in the Thermal Cut Off Kit PartSelect Number PS334299 with a multi meter to check the continuity. Hope this helps!
Does this door gasket fit my model? Medc215ew1
Thanks
For model number MEDC215EW1
Hello and thank you for writing.
No, but seal # PS11773177 is in the list of compatible parts for your model number. This front panel seal kit doesn't include the plastic retainers, reuse the old retainers. No glue is needed, the seal stretches to fit. We hope this helps. Please contact us anytime if you require further assistance.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Manolak from MURFREESBORO, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
13 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door seal busted
I took dryer door off, put on a flat surface, used pliers to pull old seal off, use a brush to clean any remaining fibers, applied adhesive & let it dry for minute or two til tacky then install seal, let dry for 24hrs, put dryer door back on & done.
Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.
Kenneth from N RIDGEVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wore out gasket
removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy
diora from ROCKFORD, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Seal damage
Very simple remove door pull off old seal, apply small amount of adhesive around seal seat. Install seal to door let cure for several hours over night is best
Vincent from RAYMOND, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad door gasket
Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout