Quick Question!

Have you ever purchased from PartSelect.com before?

11728054-1-S-Whirlpool-W10841091-SCREW
11728054-1-S-Whirlpool-W10841091-SCREW https://www.partselect.com/Schematics/Maytag/32567.gif

SCREW

Your Price

$2.85
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11728054
Manufacturer Part Number W10841091
Manufactured by Whirlpool

Sold individually.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Estate, Roper, Jenn-Air, Inglis, Amana.

This part works with the following products: Microwave, Wine and Beverage Cooler, Refrigerator.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.3 / 5.0, 2 reviews What's this?
1-2 of 2
 

240 of 425 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Charlene from San Jose, CA

Replace cracked microwave handle

Don't order the two screws. They are common screws you probably have in your garage.

After unhinging the microwave door, be carefeul taking the door apart. Do it over a kitchen counter covered by a towel padding. It came apart suddenly and half of it fell on the floor, but didn't break.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Richard from PRINCETON JCT, NJ

Door handle failed (cracked at mount)

KitchenAid Microwave [Model: KHMS 145 JBS-0]Door Handle Repair
Tools and Parts
• Door Handle [Part # PS390101]
• Putty Knife
• Phillips Screwdriver
• Tray (cup) for parts during disassembly/reassembly (3 screws on door; 2 screws on handle; spacer on top-door edge).
Instructions
• Preparation
o Disassembly can be managed with the door mounted on the unit. The handle is attached by 2-screws that can be accessed only by separating the outer/inner door panels.
o Before starting the project, watch the Youtube.com video for a GE Microwave, which is the most applicable video for removing the collar [i.e., plastic bezel around the viewing window on the inner door) and for separating the outer/inner door panels ].

• Remove the collar
Photo 1: Inner-side clip (bottom of collar) used on
3-sides of the collar (top edge is a spacer) Photo 2: Hinge side clip (right edge)

o As indicated in the video, small clips are on the inner-side of the collar on 3-sides (top, bottom, and open-door edge).
o The clips are on the outside of the collar for the door-hinge side.
o These clips are small and somewhat fragile – once a few are popped, finger pressure will generally pop the remaining clips.


• Separate the outer/inner door panels

Photo shows the inner/outer doors separated, and the 3-screws removed.
o Remove the 3-screws on the door edge before separating the outer door panel.
o There is a plastic spacer on the top, outside edge of the door that is not cemented. Remove the spacer after separating the door panels.
o Use a putty knife to pop the clips for the outer-door panel around the top, bottom, and open-door sides.
o The top door corner (the spacer edge) is tight and should be gently pushed back.
o The outer door panel will remain attached on the hinged edge and function like a second door – move gently.
o The viewing glass is clamped in place; but, handle with caution.

• Remove the Door Handle
o With the outer/inner panels separated, remove the two screws holding the handle and remove the handle.
o Retain the screws for later use.

• Install the new Door Handle
o Reuse the original screws (Note, [Part # W10841091 – screw] is a different thread, and is not self-tapping)
o The door-handle screw holes are not tapped; so insert the old screws in the handle to tap before installing the handle, leaving approximately 1/8 - 3/16” exposed.
o Remove the screws and reuse to install the handle.


Comparison of 2-original screws vs. replacement screw (note thread gauge differences).
• Reinstall the Outer Door Panel
o Align the spacer with the inner-panel edge in the upper corner.
o Close the outer panel, gently snapping the clips into place.
o Reinstall the 3-screws on the door edge.

• Reinstall the Collar
o Snap the hinge side in place.
o Gently snap the remaining sides in place

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11728054
Manufacturer Part Number: W10841091
Brand Model Number Description
Kenmore66560601000Microwave
Kenmore66560609000Microwave
Kenmore66560612000Microwave
Kenmore66560617000Microwave
Kenmore66560619000Microwave
Kenmore66560622000Microwave
Kenmore66560629000Microwave
Kenmore66560632000Microwave
Kenmore66560639000Microwave
Kenmore66560652000Microwave
Kenmore66560654000Microwave
Kenmore66560657000Microwave
Kenmore66560659000Microwave
Kenmore66560682000Microwave
Kenmore66560689000Microwave
Kenmore66561601100Microwave
Kenmore66561609100Microwave
Kenmore66561612100Microwave
Kenmore66561612101Microwave
Kenmore66561614100Microwave
Kenmore66561614101Microwave
Kenmore66561617100Microwave
Kenmore66561617101Microwave
Kenmore66561619100Microwave
Kenmore66561619101Microwave
Kenmore66561622100Microwave
Kenmore66561624100Microwave
Kenmore66561627100Microwave
Kenmore66561629100Microwave
Kenmore66561632100Microwave