Ice Door Kit W10823377 | Official Whirlpool Part | Fast Shipping | PartSelect
Quick Question!

Have you ever purchased from PartSelect.com before?

Ice Door Kit – Part Number: W10823377
Ice Door Kit – Part Number: W10823377 https://partselectcom.azureedge.net/Schematics/Maytag/MWAJKNP1.gif

Ice Door Kit

20 Reviews
Your Price
$51.24

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11723180

Manufacturer Part Number W10823377

Manufactured by Whirlpool

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door, frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Roper, Amana, Inglis, Dacor, Thermador

This part works with the following products: Refrigerator

This part fixes the following symptoms: Ice maker won’t dispense ice | Door Sweating | Leaking | Door won’t open or close

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Where can I find the video showing how to replace this part- the ice door repair kit? I have the kit but need the instructions on how to replace it.

Ann Collier
August 29, 2017
Answer:

Hi Ann, Thank you for the question, Please see below for a link to the video. https://youtu.be/2UVP9vBbxGQ Hope this helps!

18 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Trying to find the install video of the ice door kit part # w10823377

Bill for model number KSRS25FGSS14
October 23, 2017
Answer:

Hi Bill, Thank you for the question. Please see the link below for the link to the video. Good luck with the repair! https://www.youtube.com/watch?v=2UVP9vBbxGQ

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Refrigerator only disbursed crushed ice and not cube ice. What do i need to repair this. Thank you

Lorie for model number KSCS25INSS00
December 8, 2017
Answer:

Hi Lorie, Thank you of your question. It is likely that your dispenser control board may be the issue. I hope that helps. Good luck with your repair.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

What is the price of the whole freezer door

leroy for model number GD5RHAXSS00
March 2, 2018
Answer:

Hello Leroy, thank you for your question. I looked up the part and it is listed as No Longer Available/Discontinued so we are unable to provide a price. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

There is a small door inside the freezer that the freezer door closes against or near when door is closed. When the freezer door is open, that little door is open and the ice maker does not make ice. A broken off tooth pick was wedged in to hold door closed. It now makes ice but keeps making ice and doesn't stop. Not sure what to do.

Curtis for model number KSC25INSS01
March 1, 2018
Answer:

Hello Curtis, thank you for your question. It sounds like the ice door kit is sticking open and allowing ice to come down from the ice bucket all the time. If this is the case, you will want to replace the Ice Door Kit W10823377 so that door can open and close properly.You might also want to check the Emitter and Receiver Boards part number W10757851 to make sure they are functioning. To test the board you need to open the freezer door and look at the status LED on the right hand side. Make sure the ice maker control is turned “ON”. The status LED should blink twice, pause, and then repeat,blink blink…. pause, blink blink… pause.Next with the freezer door open, hold down the flapper door on the left side to unblock the optics beam. With the optics unblocked, the LED should light up and stay lit with no blinking. If the status LED continues to blink twice , then you have defective optic boards and they will need to be replaced.If there is no LED light on, then the ice maker could be in “harvest” mode. Hold down the freezer light switch, the status LED should flash every second while in harvest mode. If the LED light still does not flash, then the optic control boards will need to be replaced. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

We recently had a power outage. When the power came back on, my ice maker works fine, but it seems like the motor that makes the ice come out of the door isn't working. At first i thought maybe because the ice got a little bit watery something might be frozen, but there isn't an ice buildup. Would it make sense that this is the part that i would replace? Thanks in advance for any help.

Julie for model number gs5shaxnl00
September 18, 2017
Answer:

Hi Julie, Thank you for your question. This part could be the problem however you may also want to check your ice dispenser motor as well. I hope this helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer

Most Recent

Question:

A video for ice door kit installation

Jackie for model number 106.56703500
20 days ago
Answer:

Hello Jackie, thank you for your question. We have an installation video on our site for that part. You can go to the following link https://www.partselect.com/PS11723180-Whirlpool-W10823377-Ice-Door-Kit.htm I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

My ice dispenser started spitting water all over the freezer and not going into the cube maker to make the ice, what could be wrong, if we need a new unit, how do i change this because i see there are wires hooked up to this unit.

Kim for model number 10659122801
April 30, 2018
Answer:

Hello Kim, thank you for your question. The water should be coming from the water line at the back of the freezer and pouring directly into the ice maker itself. If it is getting all over the inside of the freezer, I would recommend checking the fill cup (part number W10122561) for any cracks or breaks, as well as the water line ( part number W10823511) and Water tube chute part number WP2209774. You might also want to check the ice maker itself to be sure there are no cracks in the ice maker mold (the part the water sits in to freeze). I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Ice isn't dispensing, the problem is the auger is broken. Could just the auger be ordered?

Claude for model number GD5LHGXKT01
April 16, 2018
Answer:

Hello Claude, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS3500972. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Unit dispenses water, and makes plenty ice. No happens when we push lever for ice. No hum from auger motor.

Sammy for model number ED5GVEXD07
February 16, 2018
Answer:

Hi Sammy, Thank you for your question. There are some parts that you will need to check to see which one is causing the issue. You will need to check the ice bin auger drum, the control bracket, the ice door kit, the micro switch, the ice guide, the ice dispenser motor coupling, the ice maker, the water inlet valve and the ice dispenser door chute. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

When i press the ice dispenser i hear a hum but he auger motor does not engage. I replaced the auger motor and the same issue is occurring. Any ideas?

James for model number KSCS25FKSS01
January 8, 2018
Answer:

Hi James, Thank you for your question. I would suggest checking your ice solenoid. I have listed that part below for you. Test it with a multi meter to see if it is working correctly. It sounds like it may be that part. If that part is fine, try your micro switch in your dispenser area. I hope that helps. Good luck with your repair.

Related Parts: Soleniod Assembly
Was this helpful?
Show Answer
Hide Answer
Question:

Water leaks from the ice dispensing. When dispensing ice there is a stream of water that comes out with the ice. Does not appear to be a constant stream but maybe a build up of water that runs out. What are the possible problems and solutions?

Alan for model number MSD2550VES01
January 3, 2018
Answer:

Hi Alan, Thank you for your question. There could be a number of things that might be the issue. I would suggest checking your dispenser ice door to make sure that it is sealing correctly against the ice dispenser opening. If it is not, you may have to check the thermostats inside of your freezer and make sure that they are working correctly. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

The ice dispenser only dispenses cube ice - even when the crushed ice feature is selected. What part do we need to repair this problem? Thank you.

Deb for model number Kenmore Coldspot 10650532100
December 31, 2017
Answer:

Hello Deb, Thank you for your inquiry. We would recommend checking the auger assembly and making sure that there is no ice clogging the blades which crush the ice. Examine each of the blades to see if any of them are bent. Also check the motor and the coupler. Hope this helps!

Was this helpful?
Show Answer
Hide Answer

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 35 reviews What's this?
1-15 of 35
471 of 554 people found these instructions helpful
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Customer:
BILL from BATESVILLE, MS
Front door ice wouldn't work and air going into freezer
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

113 of 131 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Customer:
helen j from murrells inlet, SC
Where ic e dispencer spring is held to door broke at mold
after ordering ice dispencer repair kit, and removing the outer parts found out that the problem was the ice dispencer door shell . this part is no longer available.It seems to me that if whirlpool wants to have return customers they have to stand behind the product. Well I made a L bracket and drilled a hole to to recieve the spring keeper and glued this to the housing and used a 3 1/12"finishing nail as the pin all works fine

Help other customers find the most helpful instructions.

Were these instructions helpful?   

103 of 125 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Customer:
David from Chesterfield, MO
Warm air getting into freezer
Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring panel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

44 of 52 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Customer:
Ray from San Antonio, TX
Ice door was broken
1) At bottom of ice maker trim there are two small slots at right and left ; use screw driver to pry away from door; lift trim upward away from door 2)using 1/4" nutdriver remove screws from 4 corners, 3) remove 2 screws from control panel 4) disconnect all wires/cables and set exterior panel aside. 5) locate 2" pin that runs through door spring and use needle nose pliers to remove round clip on left end of pin don't lose this clip 6) while pushing ice maker lever (where you would push with your glass) use needle nose to pull the long pin out to the right 7) Remove all remaining parts by hand (i.e. the pin, the dash pot and white lever and the ice door) 8)slide new control lever into slots on exterior side of the new door 9) -tricky part- using needle nose, push pin back through the right hinge point, the new lever, the new door, the new spring and the left hinge point (note the new door has no electric wire connector) 10) using the needle nose, carefully replace the little round clip on the left end of the metal pin. 11) reconnect all the wires (don't worry about the wire that had been connected to the door wire, just fold it aside) 12) replace two screws screws in control panel and four screws at corners of exterior panel 13) snap outer trim panel back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

33 of 43 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
Dwight from Marietta, OK
Door chute broken
First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

25 of 31 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Customer:
Frank from Sandy, UT
Ice door would not close
I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 24 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Customer:
David from Winston-Salem, NC
Ice distribution door broke
At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

18 of 22 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Customer:
Robert from Valencia, CA
Ice dispenser freezing up, dispenser door not closing completely.
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 21 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Joseph S from Las Vegas, NV
Ice door holder arm broken
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 25 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
John from Willington, DE
Broker door on ice shute
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 24 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Customer:
Thomas from Clearwater, FL
Door chute mechanism broke / air flow into ice maker
Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 10 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Customer:
Carl from Mt Juliet, TN
Plastic door bracket for icemaker chute broken
Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 11 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Customer:
Daisy from MIAMI, FL
Ice tray and door funnel woulf freeze
took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.

It was great repaired the problem for under $60

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 18 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Customer:
Ralph from Sulligent, AL
Ice dispensing door would not close
On the bottom of the cover plate are two slots. Insert thin bladed screw driver and pry out gently. Remove electrical connection plate. Remove the old door by removing pin from spring and retaining bracket useing long nose pliers. Install new door kit making sure you use all the parts in the kit. The door buffer is different and the new kit does not require a heater.Install the electrical plate, ice shute and front cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 18 people found these instructions helpful
Parts Used:
  • Ice Door Kit
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Customer:
JENNIFER from NORTH CREEK, NY
Ice door would not close
The part came with minimal instructions .... "use all the parts in the kit". That is it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 35
Customer Reviews
Average Rating:
20 Reviews
4.2
out of 5
Filter By Rating:
  • 5 Stars
    13
  • 4 Stars
    3
  • 3 Stars
    1
  • 2 Stars
    1
  • 1 Stars
    2
Sort by:
Sort by:

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11723180
Manufacturer Part Number: W10823377
Brand
Model Number
Description
Kenmore
106.52574200
Refrigerator - Kenmore Refrigerator Model 106.52574200 (10652574200, 106 52574200) Parts
Kenmore
106.58289990
Refrigerator - Kenmore Refrigerator Model 106.58289990 (10658289990, 106 58289990) Parts
Kenmore
106.5858782
Refrigerator - Kenmore Refrigerator Model 106.5858782 (1065858782, 106 5858782) Parts
Kenmore
106.59512290
Refrigerator - Kenmore Refrigerator Model 106.59512290 (10659512290, 106 59512290) Parts
Kenmore
106.5951799
Refrigerator - Kenmore Refrigerator Model 106.5951799 (1065951799, 106 5951799) Parts
Kenmore
106.59782290
Refrigerator - Kenmore Refrigerator Model 106.59782290 (10659782290, 106 59782290) Parts
Kenmore
10641522500
Refrigerator
Kenmore
10641523500
Refrigerator
Kenmore
10641524500
Refrigerator
Kenmore
10641529500
Refrigerator
Kenmore
10644022600
Refrigerator
Kenmore
10644022601
Refrigerator
Kenmore
10644022602
Refrigerator
Kenmore
10644022603
Refrigerator
Kenmore
10644023600
Refrigerator
Kenmore
10644023601
Refrigerator
Kenmore
10644023602
Refrigerator
Kenmore
10644023603
Refrigerator
Kenmore
10644024600
Refrigerator
Kenmore
10644029600
Refrigerator
Kenmore
10644029601
Refrigerator
Kenmore
10644029602
Refrigerator
Kenmore
10644029603
Refrigerator
Kenmore
10644032600
Refrigerator
Kenmore
10644032601
Refrigerator
Kenmore
10644032602
Refrigerator
Kenmore
10644032603
Refrigerator
Kenmore
10644033600
Refrigerator
Kenmore
10644033601
Refrigerator
Kenmore
10644033602
Refrigerator