This auger motor is for refrigerators.
Auger motor turns the auger that pushes the ice cubes through the dispenser chute.
Safely store any food that could deteriorate while the power is off. Unplug the refrigerator before installing this part. Wear work gloves to protect your hands.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
James N - June 5, 2020
Verified Purchase
Quick and easy.
Good youtube plus part equals money saved !!!
★★★★★
★★★★★
Russell W - June 13, 2019
Verified Purchase
Making ice in the morning.
So far the parts I’ve purchased are twice as good as what came in my POS Whirlpool. Real easy to install.
★★★★★
★★★★★
David B - June 7, 2019
Verified Purchase
ice dispenser repair
it all went very well, quite pleased.
★★★★★
★★★★★
Pinson C - January 21, 2019
Verified Purchase
Blower motor works as expected
New part received in great condition. Came on time. replacement was done and my gas .boiler was working properly. Thx
★★★★★
★★★★★
Gayle M - January 3, 2019
Verified Purchase
Very easy to install
Part was just as described and fit perfectly. Will definitely order from this site again.
★★★★★
★★★★★
Candace B - December 11, 2018
Verified Purchase
Works Perfectly!
Thanks for the help and support!
★★★★★
★★★★★
David B - December 3, 2018
Verified Purchase
Easy repair
Works great !
★★★★★
★★★★★
Roger H - October 22, 2018
Verified Purchase
Didn't fix the problem
Replaced the motor and switch. Possible defective motor. Asked for help. Received none
October 23, 2018
Hello,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
★★★★★
★★★★★
Billy W - June 20, 2018
Verified Purchase
Easy repair.
The new motor works perfectly and accomplished the repair I was needing.
★★★★★
★★★★★
Jamie B - April 10, 2018
Verified Purchase
Great improvement.
The new motor came with a rubber gasket that blocks water from rusting the motor. Original part did not have one. My ice comes out at a 100% efficiently rate!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Ice make auger stopped working
I carefully matched the model number to replacement part cross-reference and ordered the Part. You-tube instructions were accurate except for the plug wire that prevented removal of the auger motor. It took significant maneuvering to drop the old motor. The new motor fit in better but the male plug configuration did not match the f
... Read moreemale plug from the refrigerator.
A lot of wasted effort and time as well as expense! What good is matching replacement parts when the replacement is not correct?
Read less
John from WADING RIVER, NY
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Augur Motor not Working
Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice
... Read morewith fingers!
Read less
Mark from WISC RAPIDS, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
POS fridge is constantly under repair.
Understood the problem by removing the old dispenser first. That made me realize I also needed the shaft. Went online and matched up all the #’s and the repair went smoothly.
Icecube dispencer stopped working because of lack of water seal on motor shaft.
I removed the ice bucket and motor cover on the inside of the left door. Then I removed the 4 screws that hold the motor in place and unplugged the electrical connector. The old motor shaft was all rusted and housing was cracked letting water inside the motor. That's why it failed. The new motor I ordered from Part select came with a rubb
... Read moreer seal that I slipped on to the motor shaft. That will stop any water from entering the new dispencer motor. I reinstalled motor and the dispencer works great. Total time for removal and replace was 20 min. A novice can do it. Bill WI.
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or sp
... Read morein it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
Read less
Jason from Roanoke, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice dispenser motor burnt out, water got inside.
Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy.
... Read more called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.
Read less
Blye from Victoria, VA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
84 of 119 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
13 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
LELAND
December 14, 2018
The motor that turns the auger and crushes the ice cubes is broken. Everything else within the ice cube maker seems to be working. I just can not activate the motor to crush or dispence the ice cubes. Is this the correct part for replacement? Looking at that portion of the ice maker, it appears there are just two or three hex nuts to remove and then lift out the assembly. Am i correct? The new motor would be replace there and then reassemble? We can dispense water but not ice cubes. Thank you!
For model number ED5FHAXVS
Hello Leland, Thank you for your inquiry. Yes, this would be the correct part number for the motor to activate the auger and blades. We have found the following installation instructions: remove access panel and disconnect the wire. Remove the 4 screws that hold the motor in place. Place rubber washer (that is supplied with new motor) onto shaft. Replace new motor and connect wire then install access panel. Hope this helps!
16 people found this helpful.
Was this helpful?
Thank you for voting!
Frank
November 14, 2017
Is there any way to test the motor? Is it possible for the motor to have simply frozen and just needs to thaw out and be reinstalled?
Hi Frank, Thank you for the question.I suggest removing the motor to tray and unthaw it first.Here are a few things to check that might cause the motor to freeze up.Check for an air leak or gap in the door gasket. You can also check the dispenser door for an air leak, and the ice dispenser flapper door for proper closure and seal. Make sure the freezer compartment isn't too cold, the average temperature should be 0 to 5 degrees. Hope this helps!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Ken
February 3, 2020
While trying to dispense ice cubes, switching over to crushed ice, ice stopped dispensing and will not dispense either crushed or cube. Water dispenser still works, as well as making ice. Emptied the ice bin to check auger (was not stuck), but still no dispensing. Immediately after the stoppage occured could smell electrical/electronic burn/melt odor. Everything else within the ice cube maker seems to be working (making ice cubes, dispensing water). Did an inspection of the control panels circuit board, nothing visually burnt/melted. Is the motor the correct part for replacement? Or should i be looking at sensors, switches, etc. Thank you!
For model number Kenmore 10645423800
Hello, Thank you for your question. I would look into the motor, because it if it not allowing any ice through then that could be why if the motor is not turning. We hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Kevin
December 7, 2017
Freezer stopped working and the ice maker. Motor was running and making loud noise. Finally stopped making noises. Checked motor and it was hot while still plugged in. Do I need to replace the motor only.
For model number Kfis29bbms00
Hi Kevin, Thank you for the question. Unless there is visible damage to the wire harness, you should be able to replace just the motor assembly.Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Thomas
November 16, 2018
Motor does not turn to deliver ice through the door
For model number Ksrv22fvms02
Hi Thomas, thank you for your question. It is likely then that you will have to replace your motor. However you may want to take a look at your auger shaft and make sure it has not stripped. You could also take a look at the micro switch on your dispenser area as well. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Phil
January 28, 2019
Kitchen aid side by side fridge , model number KSF22C4CYY00, ice machine auger in freezer door does not work, is there a switch that operates motor. Auger part number w10822606. Should I just replace motor?
For model number KSF22C4CYY00
Hello Phil, Thank you for the question. If there is no damage or wear tot he shaft or washers, it is recommended to replace the motor. Thank you for your inquiry, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Annette
December 30, 2019
Motor (w10215646) is out, i found it on your site. The main question i have is the ice maker stops making ice for a few weeks and i put bag ice in the bucket. (that’s what broke the motor. Ice too hard). Then after a time it starts making ice again. Have you run across this problem with one stoping then after a few days start back to making ice again?
For model number BFT2673BEW10
Hello Annette and thank you for writing.
Actually we have, it turned out to be the water inlet valve being faulty. The model number you provided is not recognized. Please verify the number you provided us. If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part! We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Phil
January 28, 2019
Auger motor in door does not spin , probably bad motor, but is there a switch or micro switch?
Hello Phil, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
Was this helpful?
Thank you for voting!
Barry
November 2, 2021
My in door ice maker stopped working when I push the out side lever to dispense ice all that happens is a loud groan as long as the lever is pushed. Is this an indication that the motor is bad and a new motor needs to be installed or is it another problem. Please advise
For model number GC3SHAXVA00
Hello Barry, thank you for your question. There could be a few things causing your dispenser to not dispense ice. It could be that your ice is frozen into chunks that the auger cant break apart or push out. In this case you would have to defrost the icemaker. If the auger is not turning at all, you should verify the motor is operating. Part number PS733947. You can check it for continuity with a multi-meter. Remove power from the appliance before performing this test. If the motor has continuity then you should inspect the actuator, part number PS11749101 and switch, part number PS11738948. Remove the control panel cover and verify that the actuator contacts the dispenser switch properly and if not, check the actuator housing bracket, switch mounting bracket and the actuator pivot. Replace any defective parts. If the actuator is contacting the switch, you will need to check the switch. Set your multimeter to the lowest ohms of resistance and test your switch. If it does not read any continuity, then your switch is indeed faulty. If all of these parts check out we recommend replacing the control board. Part number PS11749617. We hope this helps.
The ice maker is making ice. The ice dispenser is very slow to dispense ice, it seems you have to shake up the ice in the ice bucket to get it to come out of the ice dispenser on the door. Do you think it is the "ice bucket auger" is what needs to be replaced? Will the ice bucket auger being replaced, make the ice come out faster?
For model number WRX986S1HZ00
Hello Paula, thank you for your question. We have researched the model you have provided, and we would suggest the Ice Bucket Auger, part number PS11723175. If you need help placing an order, our customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
