Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the outer washer tub.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
Ask our experts a question about this part and we'll get back to you as soon as possible!
19 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 13, 2017
How many shocks does this unit have and is it advisable to change all four shocks even if only one is bad?
For model number MFW9700SB0
Hi David, Thank you for the question, yes we suggest replacing all the shocks as one bad one can pout extra wear on the others.There are 4 shocks required for this appliance. Hope this helps!
25 people found this helpful.
Was this helpful?
Thank you for voting!
April
November 1, 2017
How can you tell which or if all shock absorbers are bad? My washer shakes very bad with every load no matter if small or large loads.
For model number WFW9151YW00
Hi April,
Thank you for your question. There is a sure fire way to tell if the absorbers are bad. When you remove the part, if you are able to very easily (with little effort) pull part the two pieces that make up your shock absorber apart. I hope that helps. Good luck with your repair.
15 people found this helpful.
Was this helpful?
Thank you for voting!
David
September 9, 2017
I need to replace a shock absorbor. Top bracket is broken. How do i release the bottom bracket? Dave
Hello David, thank you for contacting us. We have a how to video that shows how to remove and install the shock absorbers. You can follow the link below, hope this helps!
http://www.partselect.com/PS11723173-Whirlpool-W10822553-Shock-Absorber.htm#RepairVideo
4 people found this helpful.
Was this helpful?
Thank you for voting!
Brenda
March 23, 2018
How many shocks does this unit have?
For model number MFW9700SQ1
Hi Brenda, Thank you for the question. There are normally 4 shocks, two in the back and two in the front. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Graham
December 10, 2019
I recently asked the question. How many shocks does this machine require.? ( it had only three installed from factory. ) the answer i received: this machine requires four shocks. new question: are you sure about that.? parts list for this model says (3) shocks. can you please confirm. thank you.
For model number MHWE200XW00
Hello Graham, thank you for your question. Most washers have 4, but if your unit was only equipped with 3 then there would only be 3 on your unit that would be replaced. This part is used on multiple models and some take 3 and some take 4. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Cindy
November 6, 2019
How many shocks are attached to the tub of the washer? Since it probably best to replace all at the same time i want to be sure i am purchasing the correct amount. Thanks.
For model number wfw9151yw00
Hi Cindy, thank you for your question. Most washers have at least three. You may want to take a look inside of your appliance just to double check whether or not you have three or four shock absorbers. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ned
March 23, 2023
Machine has 3 shocks vibrates shakes a lot need to replace 1of the shocks it’s got openings for 5 don’t know how many shocks there should be on this model
For model number YMHWE251YL00
Hello Ned, thank you for your query. According to our research, there are three shocks in your washer. We would recommend checking the following parts to fix the shaking issue: shock absorber, part number PS11723173, spring, part number PS993023, and leveling legs, part number PS11738005. We hope this helps, good luck with this repair!
I was wondering how you know that your shock absorber is bad?
For model number WFW9600TA01
Hello James, thank you for your inquiry. Front-loaded washing machines have shock absorbers that are used to diminish the tub movement inside the machine. If these shock absorbers are damaged or worn out, you will hear loud banging sounds during the spin cycle. If this is the case, the shock absorbers will need to be replaced. If the washer is shaking and moving, then the shock absorber is the culprit. We hope this information is useful!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Merrill
November 10, 2019
I have taken the shock absorbers out of my front load washer. The machine shakes and vibrates violently. How can i tell if the shock absorbers are faulty?
For model number 592-49182
Hello Merrill, thank you for your question. There is a sure fire way to tell if the absorbers are bad. When you remove the part, if you are able to very easily (with little effort) pull part the two pieces that make up your shock absorber apart. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Graham
December 7, 2019
How many shock absorbers does this machine require. There were only three installed from the factory but there are spots for at least five shocks. Machine rattles, shakes, and moves when in rinse or spin cycle. Thanks
For model number MHWE200XW00
Hello Graham and thanks for writing.
There are 4 shocks required for this model. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Part Videos
Replacing your Whirlpool Washer Shock Absorber
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Paul from TARPON SPGS, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum was out of balance
Easy fix, I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel. P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier. Good luck on your repair
wilfredo vega from STRATFORD, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
shocks showing their age
Overall, the install was easy. Just a matter of getting yourself to get it done. The video on the removal / install procedures was most helpful. The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws the cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected. Anyway, certainly a project that any DIYer can tackle. Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install. Scott
SCOTT from COLCHESTER, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
8 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer shook and made noise during spin cycle.
Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.
Homer from Windham, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
3.7
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
2
2 Stars
0
1 Star
1
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Arie V - May 28, 2019
Verified Purchase
Easy repair
It took less than 10 minutes and the wash machine is running geat again..thanks for the video too
★★★★★
★★★★★
Gary A - May 14, 2019
Verified Purchase
Washer shock absorber
The parts came quickly and installed very easy. Works great
★★★★★
★★★★★
Bethany D - April 3, 2019
Verified Purchase
Front are easier to replace than rear.
I bought these parts and changed all 4 shocks because my washer was vibrating out the door and making loud noices. That was not the problem.
★★★★★
★★★★★
Shad M - March 20, 2019
Verified Purchase
Replaced the shocks.
This site tells u that there are 4 shocks for this model but there acually is only 3. Also it tells u to remove the entire front cover including the buttons to replace them when acually all u have to do is remove the little 8 inch cover at the bottom
★★★★★
★★★★★
Teresa S - September 4, 2018
Verified Purchase
Whirlpool Washer shock absorber
Found this part on another site for half the price shortly after I ordered it. Conveniently, your system does not make it easy to cancel orders. Bottom line your prices are double as the other site! Would never buy from you again.
★★★★★
★★★★★
Ralph C - June 10, 2018
Verified Purchase
Easy repair
Easy installation,still having problems with washer shaking
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
