This water level switch senses the level of water in the inner tub.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Washer Water Level Switch
Troubleshooting
This part works with the following products:
Washer.
Part# W10820051 replaces these:
3366848, 3950422, W10339229
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
washer overflowing
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out. I respect that electrical parts are non-returnable as I am in the auto parts business.
GREIG from CARTERSVILLE, GA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
17 of 23 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would no longer fill to proper height--just low
removed top controls panel (not obvious),then released old switch by rotating 90 degrees (after disconnecting wires and pressure sensor tubing), then reinstalled new switch (new switch has only 3 positions, not 5 as old switch had) and reinstalled everything else.
A 'gotcha' is the plastic 'strap' on the back that anchors swit
... Read morech compartment to the back steel sheet. It is EASY to dislodge that plastic strap from the bakc panel and it drops down inside the panel--maybe to the floor, maybe not--requiring difficult retrieval. Suggest TAPING the plastic strap in place on the back steel sheet so it will not fall out.
Read less
keith from Bellaire, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
13 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Over full
First I removed the four screws, then I replace the old part whet the new part, It was easy. thank you Juan
Juan from Humble, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
10 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
January 8, 2019
How to test the water level switch?
For model number LSQ8543JQ0
Hello Bill, thank you for your question. You can check the pressure switch with an ohm meter. If the washer is empty you should read closed across pink and violet. If it is full, it should read closed from tan to violet. Hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Scott
August 30, 2017
The one I need only has two water levels low and high this will not work do you have a switch with just two water levels I'm assuming it's what they call a manual switch
For model number RAS8333RQ1
Hi Scott,
Thank you for your question. According to your model number, this is the correct part for your machine, so this would be the one that you would need to order if you are looking to replace your water level switch. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Joe
November 14, 2017
Does not fill to right level ,will wash,rinse and drain
For model number LSQ8243HQ0
Hi Joe,
Thank you for your inquiry. If your washer will not fill to the correct level, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water level switch, the lid switch, the water temperature switch, the cycle selector switch, the main drive motor switch, the lid strike and the connector. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lonnie
January 22, 2019
How many levels does this switch have? I have a Roper washing machine with a 5 water level switch but i can not find a model number on the machine.
Hello Lonnie, Thank you for the question. This switch is 3 levels. Thank you for your inquiry, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Greg
April 29, 2019
After the washer fills and the agitator goes thru the cycle nothing else happens. This is on normal and permanent setting. Please advise what part needs to be replaced. Thank you for your assistance
For model number LSQ8543JQ1
Hello Greg, Thank you for the question. I suggest testing the Lid Switch, PartSelect Number: PS11722098. The pin on the lid pushes on the lever of the lid switch to tell the washing machine that the lid is closed, which allows the wash cycle to begin. The washer will not spin if the machine senses the lid is open. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Daniel
May 27, 2024
Hello, my washing machine fills up, but it does not drain.
For model number LSQ7030LQ0
Hi Daniel, thank you for the question. We would suggest checking the drain hose for clogging first. If it is fine, the issue could be with the drain pump, part number PS11741239. You may need to replace it to fix the issue. We hope this solves your problem!
