This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycle to begin. The lid switch mounts to the underside of the cabinet top panel. The plastic on the actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it. This part must be replaced if it is broken and no longer being activated by closing the lid (indicated by the washer not agitating properly, or the machine not detecting the lid is closed). This switch is black plastic with wire leads. It is sold individually.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not drain | Will Not Start | Will not agitate | Touchpad does not respond
Ask our experts a question about this part and we'll get back to you as soon as possible!
18 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas
July 20, 2017
How will I know if I have a bad lid switch?
Hello Thomas, great question! The easiest thing to listen for is a clicking sound. If you do not hear the clicking sound next step is to use a multi-meter tool to check for a closed continuity when shut. I hope this helps.
65 people found this helpful.
Was this helpful?
Thank you for voting!
Sam
July 20, 2017
So my washing machine is filling up with water and agitating but not draining. I did previously replace the washer pump, but I have no idea what the problem is now. Could it be as simple as the lid switch?
Hi Sam, if your washer does not drain you should check the lid switch assembly for fault first, as it is the most common problem in this case. To test it use an Ohm meter and check for continuity. If this is not the problem you will have to then test the motor, and the motor coupling. This can be tested with a multi-meter tool, and is the second most common reason for a washer to have no drain symptoms. Good luck with the repair.
28 people found this helpful.
Was this helpful?
Thank you for voting!
Sasha
July 20, 2017
The power is on in my washer, and there is nothing wrong in the fuse panel but yet my washer will still not spin. What should I check first, do you think it is the lid switch? I’m so lost, please help!
Hi Sasha, we recommend starting with the lid switch because it is the easiest and most common reason for a washer to not spin. Please let us know if you have any further questions!
16 people found this helpful.
Was this helpful?
Thank you for voting!
Lawrence
January 19, 2018
Replaced the lid switch and still nothing, won't do anything , when the old switch was in the machine was filling with water and would stop in middle of washing, but now it doesn't do anything
For model number KAWS677EQ0
Hello Lawrence, Thank you for your inquiry. I would check the timer, the water inlet valve and the control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Anne
January 3, 2019
Thank you in advance
Machine fills... does not advance to agitate... while attempting to manually advance cycle machine never engages in the agitation cycle.. can be manually moved forward to start drain spin cycle. no dial so plastic post for handle being used to move cycle forward. machine does drain and spin well. dial does click while being moved forward.
** the machine is 18/19 years old... if not too expensive willing to repair.. thank you again!!! yes i bought a new dial... that was n easy diagnosis.. :-)
For model number LSL9244EQ0
Hello Anne, thank you for your question. The most likely issue is the lid switch PartSelect Number: PS11722098. If this part does not engage the unit will not go through to the agitation cycle. I hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Rebecca
March 26, 2019
How do i know this door lock switch if for my model?
For model number WTW7000DW3
Hello Rebecca, Thank you for the question. The PartSelect Number PS11722981 is the Lid Lock Assembly listed for the model number provided. Parts are model specific and when you enter the model number into the site, it will come up with the parts lists for that appliance. Thank you for your inquiry, good luck with this repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Vince
December 17, 2017
Hi, thanks for reviewing my question. I have an old Whirlpool love the old machines they are like tanks and keep on running much longer than the new machines. The washer has four different wash cycles to choose from: Normal, permanent press, delicates and hand washables. The washer operates on the normal and permanent press cycles. However, it wont fill or advance on the delicates or hand washable cycles. It makes a noise as if it is getting power but will not start. Any help would be appreciated. Cheers!
For model number LSQ8243HQ0
Hello Vince, Thank you for your inquiry. I would check both your timer switch and your main control board with a multimeter to see if they have continuity. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Warren
December 24, 2017
I bought a switch from you guys on 6/08/2014 and never used it. It is still in a sealed package with the part number on it (3949247) order # was 6324772. Is there any way i can return this? Thanks
Hi Warren,
Thank you for your question. It is well beyond our 30 day return period and we would not be able to accept it. Here is information regarding our return policy, Parts must be in resalable condition to qualify.
All electrical parts must not have been installed.
Returned items that have been installed will not be returned to customer.
Customer is responsible for shipping returned parts back to PartSelect.
Any item received after 60 days of shipment date will not be refunded.
I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Amy
March 7, 2019
Double checking is this the right lid switch for the Whirlpool model?Thanks,
For model number LSR6132HQ1
Hello Amy, Thank you for contacting us. I have researched the model you have provided and can confirm the PartSelect Number PS11722098 is correct for your appliance. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ade
April 25, 2019
Part number for lid switch, pls
For model number LSQ7030LQ0
Hello Ade, thank you for inquiring. For your model the Lid Switch is part PS11722098.
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Repair Tip: Disconnect the power supply and fill hoses from the appliance before beginning this repair. When reinstalling the harness, take notice of the flat edges on the plastic terminal; they should face towards the front of the washer.
Replacing your Whirlpool Washer Lid Switch
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 174 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer would not start, when started wouldn't stay running.
I found the problem when I leaned on the lid while it started and that pressure kept it running. By placing detergent bottles on the right side of the lid I was able to walk away. I then bought the lid switch and lid strike after seeing it is a common problem. I watched the video and followed it almost step by step. First I unplugged the washer but didn't unhook the hose (only because I didn't have to move the washer) then I unscrewed the two screws holding the control panel, flipped it over, unplugged the lid switch connector, removed the clips holding the washer body on and tilted the body far enough forward to work on it. I replaced the switch as was done in the video and put the washer back together opposite the way I took it apart.
Pretty much like shown in the video tutorial however I didn't disconnect the water hoses. I unplugged the machine and pulled it forward 6 inches. Took it apart like in the video but because of space restrictions I took the cabinet into another room to replace the switch and then re-assembled. The hardest part was getting the cabinet to re-seat as before. It took several attempts but it's all done and the machine is working like a champ. I listed a magnet because I use them to keep the nuts and screws from getting lost
David from BREEDING, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't drain due to broken lid switch.
I followed the linked instruction video, un-hooking the power plug and water supplies, unhooking the control panel and front of the washer (tilting it forward) then removed the original lid switch. I then discovered that the lid switch plug had been revised since our washer was built and wouldn't fit the washer coupling. I then improvised by removing the new plug and splicing on the original plug to the new lid switch wiring (making sure to have the wiring match up). The washer now works perfectly.
Jeff from BUENA PARK, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would turn on, but washer would stop on rinse and spin cycle.
Unplug the power. Unscrewed 2 screws on the backside of the console to removed the cabinet. Removed the 2 clips that releases the back panel from the cabinet. Disconnect the harness. Instead of removing the cabinet i just moved the washer drum around. Was plenty of room to work with. Next I removed the 2 screws that secured the lid switch to the cabinet. Moved the drum to use a wrench to unscrew the screw that holds the ground wire in place. Moved the drum to the back and used my fingers to find the clips holding the wire to the cabinet. Re-installed the new lid switch.
Jason from CREVE COEUR, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer would fill with water and wash,but would not drain and spinn out .
Followed direction that was sent to my e-mail. My washer timer would not advance. I' am so happy for the directions sent to me from this site and being able to get the part that I, needed from this site. I, didn't have and business doing the job myself, because I'm a ill 66 year old female. There's no special instructions that I, have to add. !! Thanks !! Lewis
Susie from BRANDON, MS
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer stopped during a cycle when I lifted the lid to add another article to the wash.
I first checked to see what the likely problem was. I watched (several times) a video demonstrating how to replace the part. Figuring I could do it myself, I ordered the part. When it arrived, a friend joined me and we followed the video step-by-step. That's how we fixed the washer.
Carol from FRANKLIN, TN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Safety agitation switch quit
My son-in-law watched the video on the website and fixed it just fine.
First I unplugged the washer. siphoned out old water. I then took the decorative plates off from the top sides, with a flat head screwdriver. Removed the (2) Phillips head screws from the head, and tilted the head back. After removing the two clips from the top of the washer (near the head) with a flat head screw driver. I then pulled the body of the washer out. Tilting it back and laying it on the floor I removed the clips (Flat head) and the ground wire 5/16 socket. I then reversed, following the process step for step, putting the new switch in and putting the washer back together. Plugged it in, ran a empty small load (no clothes) with Clorox to clean tub.
Robert from DENVER, CO
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer quit mid cycle. It would not spin.
I watched your video on how to replace the lid switch. It was right on step by step. Better than the video on youtube. Just follow the instructions on the video.
Bonnie from SAVAGE, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid switch quit working. Had to push on lid to finish wash cycle.
Your video was instrumental in making this an easy job. Only hang-up we had was having to rewatch the video to see how those curly clamps went on the top. Love that you offer the repair videos!
Terry from E LIVERPOOL, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
83 Reviews
4.7
Filter By Rating:
5 Stars
74
4 Stars
3
3 Stars
0
2 Stars
1
1 Star
5
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
John H - June 15, 2023
Verified Purchase
It was so easy !
The local repairman was planning to charge me $200 plus tax to replace my broken lid switch. I bought one here and did it myself. Saved about $150.00 Now my Whirlpool washer is working perfectly even though I bought it new in 1997 - 26 years ago !!!
★★★★★
★★★★★
David R - April 30, 2023
Verified Purchase
Just what I needed!
Between the fast delivery and installation video it was a snap. The actual time it took to install was less than 10 minutes.
★★★★★
★★★★★
Arthur D B - April 20, 2023
Verified Purchase
Easy Repair, Great Part
I was having problems with my washing machine not spinning, thought it may have been the clutch. After a process of elimination it turned out to be the lid switch! Easy fix and now it operates as it should. I saved a lot of money by making this a DIY!
★★★★★
★★★★★
Crystal A - January 18, 2023
Verified Purchase
Easy Repair, Good Price
The shipping was very quick and the quality of the product was excellent.
★★★★★
★★★★★
Linda S - December 7, 2022
Verified Purchase
Easy repair extends life of my old washer
First, my washer is about 30 years old so parts are not exactly abundant. Never has needed a repair before so I was very reluctant to replace it especially after reading review on new machines. So glad I was able to find a place with the part I needed. Saved me from purchasing a new washer! The lid switch was easy to install after watching the video and reading other reviews. Took less than an hour. Hardest part was lining up the front portion of the washer after the install. Price was reasonable and shipping was fast!!
★★★★★
★★★★★
NICHOLAS H - October 27, 2022
Verified Purchase
Easy to install
Correct part, worked just fine.
★★★★★
★★★★★
Patricia M - October 6, 2022
Verified Purchase
perfect match
quality product easy to install
★★★★★
★★★★★
Alan L - April 27, 2022
Verified Purchase
Perfect fit for my old Whirlpool Washer
The item fit perfectly and works fine; albeit because of my unit's age there were a few assembly/disassembly details that I had to figure out. But I did and everything worked out well.
★★★★★
★★★★★
Victoria C - November 3, 2021
Verified Purchase
Works as advertised.
Fairly easy to install and works properly.
★★★★★
★★★★★
April L - October 27, 2021
Verified Purchase
Excellent!
Very fast shipping, exactly what I needed, and the how-to video was so easy to follow I was able to change it out myself! My washer is working perfectly again!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11722098
Manufacturer Part Number: 3949247V
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
