This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Washer Drive V-Belt
Troubleshooting
This part fixes the following symptoms:
Burning smell | Will not agitate | Spins slowly | Will not drain
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Leonidas K - June 3, 2023
Verified Purchase
wash machine part replacement
part was exactly what I needed. installed easily. glad you had the part to sell me.
★★★★★
★★★★★
Ralph L - October 16, 2022
Verified Purchase
Easy fix
The part was received quickly and the fix easy.
★★★★★
★★★★★
Patricia P - April 12, 2022
Verified Purchase
Wrong Part Received
Mistakes happen. I received prompt assistance & the correct part after contacting Customer Service.
★★★★★
★★★★★
Robert S - April 12, 2021
Verified Purchase
Replaced belt in 15 minutes.
Belt arrived promptly, and took about 15 minutes to replace. The old belt was stretched out and starting shred, causing the idler pulley to make noise. Once again, Parts Select saved me a lot of money.
★★★★★
★★★★★
Carolyn E - November 24, 2020
Verified Purchase
thrilled from a to z
as a woman i rarely am thrilled over a washing machine belt------HOWEVER--- cust service is awesome and shipping was fast---love this company
★★★★★
★★★★★
Michelle G - October 28, 2020
Verified Purchase
My washer works better than ever!!
For the simple cost of a belt, I got a brand new washer and I am so happy this company is here with instructional videos which were very helpful!! I searched for the part and here it was and everything in one place. Great experience and I will definitely be back if I need another part!!
★★★★★
★★★★★
Lloyd H - July 10, 2020
Verified Purchase
Part fit exactly and installed easily.
Belt was brand new, sealed in plactis.
★★★★★
★★★★★
HAROLD G - May 27, 2020
Verified Purchase
Perfect@
Washer stopped agitating. Watched the YouTube video, identified the bad part, ordered it and installed it. Wife now happy and impressed with my "skill" and saving $100+ over a service call. A big thanks!
★★★★★
★★★★★
Rigo C - May 27, 2020
Verified Purchase
Good part-perfect fit
My washer it’s back to normal, definitely save money instead of calling someone fixed nyself and it was easy to find the oart i needed anf i really recommend this
★★★★★
★★★★★
Charles H - March 30, 2020
Verified Purchase
Perfect match
The part was perfect
Easily installed. Washer good as new
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 27 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer pumps and drains but does not agitate or spin.
Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.
Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the
... Read more video for each part.
Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.
I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
Read less
DENNIS from EATON RAPIDS, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Smell of rubber under dryer. Inspection proved belt cracked and shinny worn spot.
Installation was easy, however watch repair instructions video for your model number to easily remove front access panel.
Fred from WOLVERINE, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)
Sharon from TEMPLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drive belt old and stretched
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs
... Read more by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.
Read less
George from Sault Ste. Marie, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
ANNA from STATEN ISLAND, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
2 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive Belt Was Noisy-Slipping
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out bel
... Read moret by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.
Read less
Steve from Carrollton, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy operation - "Chugged" during operation.
With prep work mentioned below and a good flashlight it takes about 15 to 30 minutes if you're a good handy-man. If you're not, get a neighbor or friend who is. This repair isn't rocket science, but does take a some mechanical aptitude. This unit is a washer/dryer combo unit. Unplug power cord and remove water supply hoses, the drain h
... Read moreose and dryer vent if required to obtain easy access to front panel. There is water in all the lines, so have some towels and a small gallon bucket to help drain the lines if disconnected. Remove two screws on bottom of front panel. Be sure there is about 2 inches from washer/dryer to floor in front to allow front panel to drop directly down, then pull panel out lightly. Wood spacers or similar are recommended under front feet to prop-up front of washer. (There are two tabs on each side of the front panel. The panel must be pulled straight down to clear tabs). Another option is tilt back the washer/dryer about 60 to 75 degrees unit to make the front panel more accessible if all is disconnected in back and you have the room to do so. Once the front panel srews are removed, you may have to place an object (thin pry bar or screw driver) between the top of the washer unit and the front panel for release (be careful not to dent or scratch the top metal or front panel. Remove front panel and set aside. Locate belt near bottom and tensioner pulley (it moves back and forth laterally), push in tensioner pulley to relieve pressure on belt and remove belt from small pully wheel at motor, then the large drum pulley wheel. Place new belt on large pulley first, then small pulley. Push in tensioner pulley and move middle of belt to the inside of the tension pulley to take up the slack. This process is somewhat hard. It takes good hand strength. Be sure the belt is aligned in pulley grooves. Place washer/dryer back in level position, re-attach water supply hoses, drain hose, dryer vent line and power cord, if removed for repair. Check for leaks in water supply lines and be certain the drain hose is well attached to the drain pipe. (This is a good time to clean or replace the dryer vent line to prevent possible lint fires.) Plug in washer/dryer unit and test as if washing a small load. Re-install front panel after successful test in run operation. The part came quickly and fit perfectly.
Read less
Peter from Lynnwood, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken belt
I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory
odell from Elizabethtown, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Belt
Very easy to install. Unscrew 2 screws and I was done in minutes. Thanks for the fast part delivery!
Stephen from Honesdale, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer was not spinning
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacem
... Read moreent took 10 minutes. The washer functional like new.
Read less
Mohamad from Chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
August 22, 2017
I have order a new v-belt from you today. Part number 134511600 as mine was cracked. I did not see on your home page a video of this installation. Could you e-mail the video. Also, is there a belt dressing that should be applied to the new v belt before installation. Thanks
For model number FEX831CS0
Hello Fred, thank you for contacting us. No belt dressing. We have a how to video on our site just below the image, you can also click the link below, hope this helps!
http://www.partselect.com/PS1146950-Frigidaire-134511600-Drive-V-Belt.htm#RepairVideo
27 people found this helpful.
Was this helpful?
Thank you for voting!
Elroy
June 25, 2019
What is the size of the drive belt
Hello Elroy, Thank you for the question. This belt is 1/2" wide x 32" long.I hope this helps!
19 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
January 11, 2018
In my Kenmore washer dryer combo how do I proceed to change the drive belt in the washing machine
For model number 41794814301
Hi Mike, Thank you for the question. You will need to remove the front panel from the washer to access the belt.Once the panel is removed you will be able to see the belt and how it fits onto the pulley. Hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Terri
February 26, 2019
Washer squeals at the start of a spin cycle and sweats during agitation. A sign that the belt needs to be replaced?The resident repairman said this washer did not have a belt and that washer needed to be replaced.
thanks
For model number GLWS1439FSO
Hello Terri, Thank you for contacting us. I suggest checking the following parts: PS1152574 Agitator Drive Block, PS418897 Tension Idler Pulley, and PS815490 2-Speed Motor with Pulley. Have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Rhea
April 2, 2019
How to change drive v belt on front load machine
For model number FAFW4011LW0
Hello, Thank you for the question. Here is a link to the how to video. Hope this helps!
https://www.youtube.com/watch?v=L9bfAp5irYs
4 people found this helpful.
Was this helpful?
Thank you for voting!
Joe
April 8, 2019
Is it same for washer&dryer combo
For model number fex831fs1
Hi Joe,
Thank you for your question. Yes, this belt is listed under your model number and it is designed to work with your washer/dryer combo. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Melissa
February 26, 2020
My dryer has had a burning smell, washer doesn't always spin, and now neither one will start, but there is power. Do you think this is the drive belt and how many will i need?
For model number FFLE3911QW0
Hello Melissa,
Thank you for your question. It is likely the belt is causing the symptoms, but it is also possible that the idler arm assembly under part PS11775626 for your model could be causing both the smell and the lack of spinning for the washer as well, so we suggest checking both parts for visible defects. We hope this helps.
