Frigidaire/Frigidaire_Thumb/4EQUPUSW.gif
See part F36 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Short-Tubed Water Inlet and Dispenser Valve without Sensor

$ 108.74   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS1145747
Manufacturer Part Number 134371210
Manufactured by Frigidaire
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
Frigidaire, Crosley, Kenmore.
Part# 134371210 replaces these:
AP3844428, 1154727
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.5 / 5.0, 7 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Water leaking from inlet hose area.
    Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
    Part arrived 2 days later, took about 40 minutes to install.
    • Andrew from Mastic Beach, NY
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      1- 2 hours
    • Tools:
      Pliers, Screw drivers
    • Parts Used:
      134371210
    7 of 10 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Wet clothes after spin cycle on front loader
    Found that the fill valve was leaking and clothes would be wet if not removed right away.
    Removed 2 screws from back of top panel and removed panel.
    Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids
    • Tracy from Brazil, IN
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Screw drivers
    • Parts Used:
      134371210
    7 of 10 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    crack in plastic housing
    first removed top of machine. removed 3 valve core wires set. Then removed left top screw on valve. Then removed vent tube to get to lower right screw. disconnected hose connect rack so valve housing could be removed & new installed. Rapped insulation around valve & installed. Put everything back together in reverse order.
    • Jim from Tucson, AZ
    • Difficulty Level:
      Easy
    • Total Repair Time:
      15 - 30 mins
    • Tools:
      Pliers, Screw drivers
    • Parts Used:
      134371210
    4 of 5 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Washer was in the garage, and we had a hard freeze. Water in the valve froze, breaking the valve.
    Took the top off the washer, removed the valve, installed the new one, back in buisness. It was so easy to order the part, and have the repair done in no time.
    • Alan from Eugene, OR
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Screw drivers
    • Parts Used:
      134371210
    2 of 4 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    the part cracked from water freezing
    First I removed the two screws that hold the part in place. I then pulled the part out about 3 inches and disconnected the three wires from the part and put the new one in
    • Kathy L from Twin Lake, MI
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      15 - 30 mins
    • Tools:
      Screw drivers
    • Parts Used:
      134371210
    2 of 4 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    The valve had cracked so water was leaking out from the cracked area.
    After getting a quote for $140 for a repair, I decided to try ordering online and hope for the best. I am delighted to say it was incredibly easy! All I had to do was remove the broken valve by unscrewing the water hoses with a wrench and remove two screws that held the valve on with a screw driver. Next, I popped in the new piece, replaced the screws with the screwdriver and attached the hoses, then tightened them with the wrench. Very easy! 10 minutes total.
    • Jennifer from Middleboro, MA
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Screw drivers, Wrench (Adjustable)
    • Parts Used:
      134371210
    1 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Washer was filling with water when not in use
    This repair was pretty simple. Unplug washer from electrical outlet and remove hoses. This is a good time to replace the hoses. Removed two screws at the back of the washer to remove the top of the washer. This exposed the faulty valve assembly. Disconnect the three connections. There are two screws holding this part in place. The top one is easy to remove, the bottom one is a little more difficult due to access. Remove plastic retainer plate on back of washer. Remove faulty valve assembly. There are two rubber grommets/gaskets that will need to be removed from the faulty part and installed on the new part. Slide new assembly into place. Secure with the two screws. Replace retainer plate. Reattach power connections. Reattach hoses and finally Reinstall top of washer. Total time was right around 30 minutes.
    • Dan from LONE TREE, CO
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Screw drivers
    • Parts Used:
      134371210
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Related Parts
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS1145747
      Manufacturer Part Number: 134371210
      Brand
      Model Number
      Description
      Kenmore
      41744082400
      Washer
      Frigidaire
      BLTF2940ES0
      Washer - Residential
      Frigidaire
      BLTF2940ES1
      Washer - Residential
      Frigidaire
      BLTF2940ES2
      Washer - Residential
      Crosley
      BTF2140ES3
      Washer - Residential
      Frigidaire
      FTF2140ES3
      Washer - Residential
      Frigidaire
      FTFB4000FS0
      Washer - Residential
      Frigidaire
      FTFB4000FS1
      Washer - Residential
      Frigidaire
      FWFB9200ES0
      Washer - Residential
      Frigidaire
      FWFB9200ES1
      Washer - Residential
      Frigidaire
      FWFB9200ES2
      Washer - Residential
      Frigidaire
      GLTF2940ES0
      Washer - Residential
      Frigidaire
      GLTF2940ES1
      Washer - Residential
      Frigidaire
      GLTF2940ES2
      Washer - Residential
      Frigidaire
      LTF2140ES2
      Washer - Residential
      Frigidaire
      LTF2140ES3
      Washer - Residential
      Frigidaire
      LTF2940ES0
      Washer - Residential
      Frigidaire
      LTF2940ES1
      Washer - Residential
      Frigidaire
      LTF2940ES2
      Washer - Residential

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service