The main drive belt is designed to work with the motor pulley and spin the drum until it comes up to speed.
NOTE: Per factory measures 48.4" at rest & 51.2" when working.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Washer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Burning smell | Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH08X10024 replaces these:
AP3884128, 1168664, WH08X10024
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
David H N - August 14, 2021
Verified Purchase
Fits perfect
Great part
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Broken Spider Arm
We ultimately rebuilt this washer because I love it so and it was one-half cheaper to rebuild than to buy new! We watched videos and researched the repair and then dove in. Yes, we had to tear the machine down but really it was not that bad of an ordeal. It ended up being much easier than we initially thought but once all the parts arr
... Read moreived we fixed it!
It. Was awasome the part fit great and it was even deliverd sooner than expected thank you
Savian from Pahrump, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
23 of 44 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear Tub Pulley became loose and deformed pulley shaft
Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley. Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfa
... Read moreces too much, because new pulley will be loose and the next step is to replace the drum shaft.($$$$) Pulley did not fit 100% (Had some slop) but that was from material being worn away from "hammering" effect. Torqued with Torque wrench and added green 609 loctite compound - this is meant to help adhere and take up some loose fit in assemblies. - Drawback to Loctite is most have to be heated to 300 to 400 degrees to remove, or pulley will need to be cut off and ruined, I further repair/removal of pulley is necessary. This is an Easy Fix/Replacement of parts.... The hard part is filing the drum shaft surfaces to accept the new pulley, and getting the belt back on - Belt is tight but needs to be stretched on like putting a bike chain back on.
Washer now spins and sounds like a dream! - Good Luck!
First I unpluged electrical cord. removed the 4 screws on the back panel. I then loosen the (1) motor bolt that you can adjust for tightness after you put the new drive belt on the round pulley. Make sure the bolt in the center of the round pulley is tight. The round pulley should not wabble. Make sure not to over tighten
... Read morethe drive belt on the motor. A slight play is fine. Put back panel on and plug electrical cord. Run washer cycle on and check. Should be OK.
Read less
Bernard from Antelope, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench (Adjustable)
38 of 60 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jack
September 29, 2017
Replace door seal, pulley,nut and drive belt,washer still making loud noisy when spinning at high speed. What can the problem be?
For model number WBVH6240F0WW
Hi Jack,
Thank you for your question. It looks like you have replaced most of the more common culprits. I would suggest taking a look at your motor. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Larry
January 23, 2019
In the spin cycle there is smoke coming from inside the washer cabinet. Tub belt?
For model number WCVH6600HWW
Hello Larry, Thank you for the question. Yes, the most common issue would be a belt. If the belt is not the issue, you may need to open up the cabinet and watch to see where the smoke is coming from during the spin cycle. Thank you for your inquiry, good luck with this repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Bob
November 3, 2019
I purchased a new belt and having trouble putting it on. Any suggestions?
For model number WCVH6800J1MR
Hi Bob, please watch video https://www.youtube.com/watch?v=Z2EVR1QA1gM . Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
