The door latch housing encloses the door switches and door latch.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Microwave, Range.
This part works with the following products:
General Electric, Hotpoint, Haier.
Part# WB06X10610 replaces these:
AP3866945, 251301302560
Customer Reviews
Average Rating:
★★★★★
★★★★★
8 Reviews
4.8
Filter By Rating:
5 Stars
7
4 Stars
0
3 Stars
1
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Kenneth W - January 2, 2023
Verified Purchase
easy repair
the part was what i needed to fix the problem. great service
★★★★★
★★★★★
Kim E - September 10, 2022
Verified Purchase
Confusing
The repair was confusing. The part was easy to replace, but it should be mentioned that a piece from the old part had to be removed and attached to the new part so the latch would work correctly. Almost had to buy a new microwave until that was realized.
★★★★★
★★★★★
Robert S - May 4, 2022
Verified Purchase
Easy Repair
The part was a bit slow in getting here via FedEx, but once it came, it only took me about 15 minutes to change it out and the microwave works perfectly now. It was the exact part I needed to fix the issue of the microwave shutting down and blowing the internal fuse if I opened the door during a cooking cycle to stir something. I thought I was going to have to buy a new microwave, but this did the trick. Very easy to replace after watching a YouTube video on how to do it.
★★★★★
★★★★★
Dennis G - March 27, 2022
Verified Purchase
Exact replacement
Identical to original. No issues.
★★★★★
★★★★★
Jon G - September 2, 2021
Verified Purchase
Works great!
Replaced my door latch housing since it had worn causing the microwave to trip my circuit breaker. This solved that issue along with replacing the two Normally open switches and one normally closed.
★★★★★
★★★★★
Charles B - September 17, 2020
Verified Purchase
Factory part, exact fit
This was an inexpensive fix for an over the range micro. A bit pricey for a piece of plastic, but the only solution other than total replacement. PartSelect had the part; it was not widely available.
★★★★★
★★★★★
Richard H - June 12, 2020
Verified Purchase
Medium hard repair.
Microwave was tripping breaker and blowing fuses and after much research and disassemblies noticed that where the door latch hit and rode up the angled part on the body was allowing the door to flex when opening just enough to activate the bottom switch before the top switch which causes a direct short. The plastic had worn unevenly on the 2 latch points and after replacement problem gone. Also these guys had the part for a reasonable price compared to everyone else. It's just a block of plastic for cripes sake
★★★★★
★★★★★
Rafael V - April 23, 2019
Verified Purchase
Fast and easy
Good condition perfect fit fast arrival. It was expensive.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
door switch monitor broke ,tripped breaker
when on line to see how to replace the micro switch, very helpful.be careful removing door latching housing & vent cover.unplug control panel & set aside so it's out of the way.
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board
... Read moreout of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Read less
Charles from CLAYTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
11 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dennis
February 23, 2022
Does this come with the interlock switches? If not, is there a part that includes the switches?
For model number JVM3160DF3WW
Hello Dennis, Thank you for the question. The Interlock Switches Part #PS8754454, Part #PS8754455 and Part #PS1019163 are sold separately. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I am looking for the door latch housing for model JVM1635SFC01. The part that holds the switches and receives the door latch. I have found WB06X10610 and WB06X10289. The first looks identical and the latter looks the same minus the extra unneeded screw holes. However, both do not state JVM1635SFC01 compatible. Is there another part # that fits model JVM1635SFC01. When looking at the the Parts Diagram for my model it looks like L01 is the door latch housing but there are no picture attached and that part is listed as Bracket Interlock part # WG02A01011. Any help is appreciated
For model number JVM1635SFC01
Hi Brett, thank you for reaching out. The manufacturer's part numbers, WB06X10610, and WB06X10289, that you have mentioned, do not fit your model. The compatible one is the interlock bracket, part number PS12340572. We hope this information is useful!
