Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Michael A - April 11, 2018
Verified Purchase
Easy Repair, but took some time to settle down.
The instructions were, for the most part, straightforward and accurate. After laying the control panel on a towel the instructions said to remove PC plug to the display and then remove the PC board. That's backwards. You can't get at the PC plug until you remove the PC board. Also, I didn't notice a rubber insulator. Installation was easy, but it took a while for the display to settle down. I wasn't expecting that. A side benefit of this installation was that I was able to access the bulb socket and replace a burned out bulb. The instructions which came with the bulb were for a different model, as were all the instructions on You Tube and other sources. You should link the instructions to both parts.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Display did not lightup but the microwave oven functioned.
I did not have to replace the part. I turn the fuse off and waited 5 minutes and turned it back on. The display came back on. I saw this recommendation on your web site after I ordered the part. You should do this before you order the part.
JAMES T from PEWAUKEE, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flashing display
Replace Advantium 120 flashing display.
Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On th
... Read moree cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing.
Read less
William from EAGLE, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
TIM
January 12, 2018
My display will not work
For model number PSB1001NSS01
Hello Tim, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: the digitron, the relay board, and the control board. Also try unplugging the microwave for 15 minutes then plug it back in to see if the display resets itself. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
January 10, 2020
Hi there, Thank you for answer my question for the possible parts to fix the microwave/oven
I was suggested to purchase the line fuse which I did and replace it in the safe matter and didn’t work what will be the next parts that will probably work? Thank you
For model number SCB1001MSS 01
Hi Michael. At this point it is likely the digitron. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Sammy
February 18, 2019
I am confuse the two board to use, digitron(1657)or display control board(2002),the problem display light not bright enough and running around, can not stop even i push any push buttons which board should i replace (1657) or (2002)
For model number ZSC1001KSS01
Hello Sammy, Thank you for contacting us. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Luther
July 24, 2019
GE advantium microwave/convection oven will not come on. Have been told parts are expensive to buy & labor high. Parts on your website very reasonable. This is a $2400.00 machine & i believe it can be repaired for a reasonable price. Do you have any recommendations or suggestions ? Repairman coming this friday the 26th to diagnose. Any help you can give will be most appreciated. Thank you.
For model number ZSC1001KSS01
Hello Luther, thank you for inquiring. You will want to consider as possible causes either the Line Fuse part number PS239525, the Terminal Micro-Switch part number PS236997, or the Oven Cavity Temperature Cut-Out part number PS235672 for your model. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Leon
December 10, 2019
Will part GE wb27x10856 serve as a replacement part for wb 27x10431 which is no longer available?
For model number scb2001css-03 GE
Hello Leon and thanks for writing.
The part you are requesting is discontinued for your model and is no longer available. We have no known replacement information in our system. We recommend you contact the manufacturer of the part to see if they have recently released a new substitute. Part #PS 1018741may fit with your unit; however, as this part does not show as being compatible with your model number, we can not guarantee that it will fit. We would suggest contacting the manufacturer directly. We hope this helps. Please contact us anytime. GE US 800-626-2005
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
January 7, 2020
I can use some help
I have a GE profile advantium 120 microwave/oven the display panel it flashes but i can’t control it
Thank you
For model number SCB1001MSS 01
Hello Michael and thank you for writing.
There are a few different reasons why this might happen; it could be as simple as a fuse, have you checked the fuse box of the house for the circuit the unit is on? It could be internal fuses PS239525 or the digitron PS1018741 itself. You should check for signs of damage, and replace it if necessary. We hope this helps. Please contact us anytime if you require further assistance.
My problem is the display keep on flashing and running around even if push the stop or any other button,is this possible cause of malfunction the board 1657
For model number ZSC1001KSS01
Hello Samson, Thank you for the question. The Digitron could be a cause. In most cases it gives a Error code 120. It can also be the Display Control Board, Part Number: PS1022528. Hope this helps, good luck with this repair!
The microwave is not powering up. No clock or other control panel lights come on. Thermostat checked good, fuse checked good. Verified outlet is providing power so it is not the breaker. Is there another part I can test?
For model number PSB1201NSS01
Hi David, thank you for the question. According to our research, this issue may be due to one or more faulty control boards. First, you may need to check the relay board, part number PS12725850. If it is not faulty, then you may need to check the power board, part number PS1020967. If there is no issue with the power board, then you may need to check the digitron, part number PS1018741. If the problem persists, you may need to check the display control board, part number PS1022528. If any of these boards is faulty, you may need to replace it. We hope this information helps!
