This impeller and motor shaft seal kit is used in dishwashers to rebuild the circulation pump. If your dishwasher has any of the following symptoms, replacing the part could be the solution: circulation pump is leaking, not cleaning dishes, not draining, making loud or odd noises. The tools needed for this repair are an adjustable wrench, 1/4 inch nut driver, 5/16 inch nut driver, Phillips screwdriver, flathead screwdriver, flat file, and needle nose pliers. Remember to unplug your dishwasher before installing this part and refer to the manual provided by the manufacturer for installation instructions and a detailed diagram.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Dishwasher Circulation Pump Impeller Kit
Troubleshooting
This part fixes the following symptoms:
Not cleaning dishes properly | Leaking | Not draining | Noisy
This part works with the following products:
Dishwasher.
Part# WD19X10038 replaces these:
AP3883871, 1168286
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.7
Filter By Rating:
5 Stars
2
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Steven A - May 6, 2019
Verified Purchase
Good kit
All the pump parts fit good, it was an easy repair and the dishwasher works great again - no leak.
★★★★★
★★★★★
James S - March 11, 2019
Verified Purchase
Pump parts replacement
The part worked great.
There was a difference. The screw in retainer ring did not have a filter strainer like the original part
★★★★★
★★★★★
Tom M - November 21, 2018
Verified Purchase
Dishwasher would not stay drained.
Did the Impeller Kit and Drain Pump Assembly at the same time as I did not want to tear the dishwasher apart twice. It has fixed the problem of standing water in the bottom of the unit.
I am satisfied and have used Part Select for other things in the past with good results.
I know it's not possible to always have every part on hand, this is the first time there was an extended back order (for the impeller kit) three weeks but still satisfied.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 1.0 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
excessively delayed delivery
I couldn't do the repair because the parts arrived a week after I left, even though I paid extra for speedy delivery. And there was ZERO customer support - the phone message said they would not answer the phone, and the email response was a generic FAQ.
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
April 8, 2018
My GE profile dishwasher makes a thumping noise and there is standing water in the bottom of dishwasher when finished. From reading descriptions, it sounds like it could be the drain pump or the circulation pump impeller. Hoping you can advise. Thanks.
For model number Pdw7900p00bb
Hello Mike, thank you for your question. It sounds like the issue is with the drain pump. If the noise is happening at the end of the cycles, when water is draining out of the unit you should replace the
Drain Pump Assembly Part Number: WD26X10025. The standing water in the bottom of the dishwasher when the cycle is completely finished is usually cause by the flapper in the drain pump being broken, or stuck open. This can also cause air to come back into the unit and cause the thumping sound. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Fred
February 14, 2018
Loud rumbling sound from area of motor while washing. Motor is turning as usual. Dishes are being cleaned, drain okay. Sometimes can stop washer, turn back on, noise stops, then resumes.
For model number GLD5860L00SS
Hello Fred, thank you for your question. If the noise is coming and going, I would recommend removing the bottom spray arm, and the pieces below that to get to the filters. Remove and clean the filters, and check down below the to see if there is any obstructions. If there is nothing noticeably there, you would probably want to check/replace the Pump and Motor Assembly WD26X10053. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
James
January 30, 2020
Dishwasher is leaking underneath. Inlet valve and hoses ok. Looks like it is coming from around motor. Drains ok. Drips most during wash cycle
For model number GE PDW7880NOOSS
Hello James, thank you for your question. We would recommend replacing the following parts. Pump Connector Part Number: WD18X10010, Inlet Sump Part Number: WD18X10008, and Circulation Pump Impeller Kit Part Number: WD19X10038. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Stuart
October 29, 2017
Middle and upper spray arms don't rotate or spray water. The bottom spray arm spins and sprays water. I have replaced the pump impeller kit and the sump. The fine filter looks clean. Now what do I do? Thanks, Stuart
For model number ZBD0710N00SS
Hi Stuart, Thank you for the question. I would check to see if the Main Conduit is blocked or damaged. This part brings water from your main water line the wash arms.You can check to make sure it did not come lose or crack where it attaches to the appliance and spray arms.Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
December 13, 2017
Is this part the likely culprit after the machine was accidently run a load without the water turned on. It still works fine but makes awful noises while washing.
For model number GLD5708V00BB
Hi Mike,
Thank you for your question. That would be my first thought, it sounds like maybe it over worked itself because there was no water inside of the machine. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jason
August 16, 2019
When running , dishwasher makes a high pitched noise that is pretty constant throughout the wash. I'm suspecting the motor. Would this kit be of any good or should i just replace the whole motor assembly
For model number ge pdwt380v00ss
Hi Jason, it is hard to say, however this kit WD19X10038 does have a good chance of fixing your issue. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dave
November 14, 2023
I was cleaning the filters and found the blade from the impeller. Took the motor out and the blade won't screw back on. Is the blade stripped or the shaft of the motor stripped?
For model number GSC3500D51WW
Hi Dave, thank you for the question. Based on our research, the blade is more likely to be stripped and may need to be replaced. The blade is not available separately, but comes as a part of the circulation pump impeller kit, part number PS1017766. Please submit a new question if you have any follow-ups!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.