Quick Question!

Have you ever purchased from PartSelect.com before?

10064583-1-S-Whirlpool-W10757851-Emitter and Receiver  Boards
10064583-1-S-Whirlpool-W10757851-Emitter and Receiver  Boards 10064583-2-S-Whirlpool-W10757851-Emitter and Receiver  Boards 10064583-3-S-Whirlpool-W10757851-Emitter and Receiver  Boards https://www.partselect.com/Schematics/Whirlpool/H9NMQPW6.gif

Emitter and Receiver Boards

Your Price

$280.34
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS10064583
Manufacturer Part Number W10757851
Manufactured by Whirlpool

These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

This part works with the following brands: Kenmore, KitchenAid, Whirlpool, Dacor.

This part works with the following products: Refrigerator.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Ice maker dispenses too much ice.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

How do you test the emitter and receiver boards for ice maker

Warren for model number KSRS27ILBL03
Answer:

Hi Warren, Thank you for the question, To test the board you need to open the freezer door and look at the status LED on the right hand side. Make sure the ice maker control is turned “ON”. The status LED should blink twice, pause, and then repeat,blink blink…. pause, blink blink… pause.Next with the freezer door open, hold down the flapper door on the left side to unblock the optics beam. With the optics unblocked, the LED should light up and stay lit with no blinking. If the status LED continues to blink twice , then you have defective optic boards and they will need to be replaced.If there is no LED light on, then the ice maker could be in “harvest” mode. Hold down the freezer light switch, the status LED should flash every second while in harvest mode. If the LED light still does not flash, then the optic control boards will need to be replaced. Hope this helps!

3 people found this helpful.
Question:

Our ice maker has stopped making ice. My neighbor came over and ran some tests on everything and figures it is probably the sensors are bad/blocked so it never thinks it needs to make more ice. I want to order new sensors for each side but dont know what parts they are by the diagram!

Scott for model number KSRG22FKWH01
Answer:

Hi Scott, Thank you for the question. We refer to the sensors as the Emitter and Receiver Boards. These boards tells the ice maker when it's full and that it has to dump the ice, and it also tells the ice maker when to refill with water. Hope this helps!

2 people found this helpful.
Question:

Ice maker display leds and water dispenser not working?

brooks for model number KSRW25CRSS03
Answer:

Hi Brooks, Thank you for your inquiry. It sounds like you have an issue with the electronic board or the emitter and receiver boards and you will test them with a multimeter to verify which part is causing the issue. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Question:

Icemaker stopped making ice. What is the part number for the replacement? Also, how can i be sure that the icemaker is the problem? Your site says the circuit board behind the flap could be he problem. Is there a way to test which is the problem before i order parts?

Brian for model number KSRL25FXMS00
Answer:

Hi Brain, Thank you for your question. I have attached the part information for your ice maker down below for you. You may also want to check your water inlet valve as well. The valve has two solenoids, one for the water valve and one for the ice maker. If the valve is not working it will not send the water up to the ice maker. You can test all of these parts with a multimeter. Good luck with your repair.

Related Parts: Water Inlet Valve, Icemaker
1 person found this helpful.

Most Recent

Question:

Ice maker will not stop making ice, even with the switch on off

kGary Meisner for model number Ksrg25fkss02
Answer:

Hello Gary, thank you for contacting us. That sounds like it would be the emitter and receiver boards. They control the ice maker functions. You may want to see about replacing that part. Good luck with the repair!

Question:

I have replaced the ice maker in which the seal was bad and the emitter boards the led is blinking twice pause then blinking twice again. When i hold in the door it keeps the same blinking pattern. When i hold in the freezer light switch there is no led, what can be wrong?

Pam Hull for model number MSD2669KEA00
Answer:

Hi Pam, Thank you for your inquiry. You may have to check the connections to the control board and the control board itself to see what is causing the issue. I hope this helps. Thank you and have a great day!

Question:

Where is the water inlet valve located and how is it tested?

Brian for model number KSRL25FXMS00
Answer:

Hi Brian, Thank you for the question. The valve is located on the back of the appliance where the water line from your home plugs into the appliance. In order to test the valve you will need a Ohm meter to check for continuity. Hope this helps!

Question:

Ice maker quit working, so I replaced it. Makes ice but will not eject it. Could the problem be the emitter and receiver boards?

Bruce for model number GS5SHAXNL00
Answer:

Hi Bruce, Thank you for the question. These boards tells the ice maker when it's full and that it has to dump the ice, and it also tells the ice maker when to refill with water, so I do not think it would be the boards. I suggest checking to see if the Auger is turning in the ice bucket and pushing the ice out. Also check to see if the ice door is opening and not stuck or frozen closed. Hope this helps!

1 person found this helpful.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 73 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: THOMAS C from LAFAYETTE, LA

Ice maker would not stop making ice.

Unplugged unit. Taped ice maker flap up and out of way. Removed screws holding emitter board, unplugged old board and connected new. Did same for receiver board on opposite side.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Douglas from Mansfield, TX

Icemaker kept on making ice

i replaced the electronic control board of emitter and receiver

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Mona from The Sea Ranch, CA

Ice maker not making ice

Removed screws holding face plates in place inside the freezer housing ... unplugged the old emitter and receiver, then plugged in the new emitter and receiver. Screwed the face plates back in place. Actually, this repair took place a few years ago. When my ice maker quit recently, I noticed the red light inside the freezer housing was not blinking properly. I remembered from my previous experience that the pattern of red light blinks was diagnostic, but of course, the pattern is not described in my owner's manual. The installation instruction sheet that comes with this part does give the diagnostic patterns, however. As it turned out this time, when I was ready to install the new parts, I discovered that one of the little ice-flipper thingies (technical term) was caught on the ice cube-freezing tray ... I released the flipper thingy, and, in time I was back in the ice-making business. So the new part is stowed away in the pantry until the present emitter/receiver parts fail ... and I made a copy of the red-light diagnostic pattern to put in the owner's manual. Now, all I will have to do when the existing parts fail, is remember where I stowed the replacement parts!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Oscar from Hurst, TX

Ice maker stop making ice

Replaced the emitter/receiver and it worked after that. Very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Ronald from Ekins Park, PA

Ice maker stopped working

A snap! The part arrived the day after I ordered it. (How, I don't know). The video showed exactly what to do. I did it. Ice maker now works like a charm. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Wrench set
Customer: Ernest from Reno, NV

Ice maker stopped working

I first ordered the electronic control boards. However, they arrived with an Instruction Sheet. The diagnostic procedures listed on that sheet identified that the optics were working properly, so did not use the electronics. That left the motor assembly as the culprit. Ordered that. The motor assembly arrived promptly and installed easily - just like the video. Ice maker began making ice immediately. Thank you PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Rick from Lorain, OH

The icemaker would not work

I tried several things first : changed the filter cartridge, then the water control valve, then the control boards but still no ice. Rather than buy a new motor assembly, I bought a whole new icemaker which included the motor assembly and finally SUCCESS! In total it cost me about $350 but you have to try the easier and cheaper things first. One 1/4" screw and disconnecting the wire harness clip plus reusing the old icemaker base and the repair was complete. I would recommend a more detailed discussion on what each part does and the way the colored wires attach. Wire clips can sometimes be connected upside down. I was very happy with how quickly I received the new part. I whole-heartedly recommend PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: PAUL from FAIR LAWN, NJ

Ice maker stopped working

I paid for a service call to have the problem diagnosed, and then ordered and changed the parts myself, saving about 50% off the original estimate.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: David from Davis, CA

Ice maker stopped working

After calling Sears and setting up an appointment and waiting 7 hours for them not to show.. without any phone call..even after the dispatcher said I was "Next on the List" I figured thilure was the Emitter boards.. I ordered theere had to be a better way.. I researched this site and determined that the most likely cause of fa parts and received them within 3 days with standard shipping. I followed the optical diagnostic instructions that were included and replaced the boards. Within a few hours the ice maker was singing again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: William from Margate, FL

Sensor board on icemaker

First I removed the icemaker and the sensor boards by removing 6/7 screws. Next, I placed the new sensors into the emitter and receiver and re-installed the components...reset the icemaker and was all done!

Last time my icemaker broke I paid a contractor $225! This time I did it myself in 30 minutes and saved $150. And it was so easy my wife could'a done it......

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Terry from Avondale, AZ

Ice maker was not producing ice.

I removed the receiver cover and replaced the board (three screws, two on the board) did the exact same procedure on the emitter board ( three on the cover, one on the board). This process took all of 4 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Mark from Georgetown, TX

Ice maker would not stop making ice.

Unplugged electrical cord for refrigerator, Removed the 3-screws for the bad Emitter, unplugged the wiring harness, plugged the wiring harness into the new Emitter put into position replaced screws, Removed screws for bad Receiver unplugged wiring harness, plugged in new receiver put into position replaced screws plugged refrigerator electrical cord back in. Working ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Stephen from Chicago, IL

No ice was being made

After reading other repair stories online, i ordered the parts, followed the included instructions to replace the boards and the next day i had a full bin of ice. This is the second refrigerator i fixed with parts from partsselect.com. They are AWESOME!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Juan from Tomball, TX

Ice maker wouldn't stop making ice then quit 1.5 days later

removed 3 screws on each side of freezer where the ice maker controls are unplugged the circuit boards. un screwed the boards from the plastic and put the new ones in, reinstalled. now, Ice and not over flowing! :)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: David from Ennis, TX

No ice no movement in ice maker

Being 50 miles from the Sears with a 7 year old unit, I actually changed out both board (a kit) which was 9 screws. 3 screws in the outside panels, and 2 in the larger board, and 1 on the smaller board. Both both boards plug in. I also changed the actual ice maker which unplugs and slides out on my unit. Remove a single screw (1/4") on bottom to remove a plastic shield that covers/protects the plug in. A plastic arm lock is in the bottom guide tray, push it up first. Then unplug the unit. Three more 1/4" screws in bottom to remove the custom plastic mount. Then reverses the process to install the new ice maker. Total $175 plus 1 hour labor. In 6 months the unit will have paid for the repairs. I hope to get 5 years of service from the job

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS10064583
Manufacturer Part Number: W10757851
Brand Model Number Description
Kenmore10641522500Refrigerator
Kenmore10641523500Refrigerator
Kenmore10641524500Refrigerator
Kenmore10641529500Refrigerator
Kenmore10644022600Refrigerator
Kenmore10644022601Refrigerator
Kenmore10644022602Refrigerator
Kenmore10644022603Refrigerator
Kenmore10644023600Refrigerator
Kenmore10644023601Refrigerator
Kenmore10644023602Refrigerator
Kenmore10644023603Refrigerator
Kenmore10644024600Refrigerator
Kenmore10644029600Refrigerator
Kenmore10644029601Refrigerator
Kenmore10644029602Refrigerator
Kenmore10644029603Refrigerator
Kenmore10644032600Refrigerator
Kenmore10644032601Refrigerator
Kenmore10644032602Refrigerator
Kenmore10644032603Refrigerator
Kenmore10644033600Refrigerator
Kenmore10644033601Refrigerator
Kenmore10644033602Refrigerator
Kenmore10644033603Refrigerator
Kenmore10644034600Refrigerator
Kenmore10644039600Refrigerator
Kenmore10644039601Refrigerator
Kenmore10644039602Refrigerator
Kenmore10644039603Refrigerator