Quick Question!

Have you ever purchased from PartSelect.com before?

10064583-1-S-Whirlpool-W10757851-Emitter and Receiver  Boards
10064583-1-S-Whirlpool-W10757851-Emitter and Receiver  Boards 10064583-2-S-Whirlpool-W10757851-Emitter and Receiver  Boards 10064583-3-S-Whirlpool-W10757851-Emitter and Receiver  Boards https://www.partselect.com/Schematics/Whirlpool/H9NMQPW6.gif

Emitter and Receiver Boards

Your Price

$280.34
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS10064583
Manufacturer Part Number W10757851
Manufactured by Whirlpool

These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

This part works with the following brands: Kenmore, KitchenAid, Whirlpool, Dacor.

This part works with the following products: Refrigerator.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Ice maker dispenses too much ice.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

How do you test the emitter and receiver boards for ice maker

Warren for model number KSRS27ILBL03
Answer:

Hi Warren, Thank you for the question, To test the board you need to open the freezer door and look at the status LED on the right hand side. Make sure the ice maker control is turned “ON”. The status LED should blink twice, pause, and then repeat,blink blink…. pause, blink blink… pause.Next with the freezer door open, hold down the flapper door on the left side to unblock the optics beam. With the optics unblocked, the LED should light up and stay lit with no blinking. If the status LED continues to blink twice , then you have defective optic boards and they will need to be replaced.If there is no LED light on, then the ice maker could be in “harvest” mode. Hold down the freezer light switch, the status LED should flash every second while in harvest mode. If the LED light still does not flash, then the optic control boards will need to be replaced. Hope this helps!

3 people found this helpful.
Question:

Our ice maker has stopped making ice. My neighbor came over and ran some tests on everything and figures it is probably the sensors are bad/blocked so it never thinks it needs to make more ice. I want to order new sensors for each side but dont know what parts they are by the diagram!

Scott for model number KSRG22FKWH01
Answer:

Hi Scott, Thank you for the question. We refer to the sensors as the Emitter and Receiver Boards. These boards tells the ice maker when it's full and that it has to dump the ice, and it also tells the ice maker when to refill with water. Hope this helps!

2 people found this helpful.
Question:

Ice maker display leds and water dispenser not working?

brooks for model number KSRW25CRSS03
Answer:

Hi Brooks, Thank you for your inquiry. It sounds like you have an issue with the electronic board or the emitter and receiver boards and you will test them with a multimeter to verify which part is causing the issue. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Question:

Icemaker stopped making ice. What is the part number for the replacement? Also, how can i be sure that the icemaker is the problem? Your site says the circuit board behind the flap could be he problem. Is there a way to test which is the problem before i order parts?

Brian for model number KSRL25FXMS00
Answer:

Hi Brain, Thank you for your question. I have attached the part information for your ice maker down below for you. You may also want to check your water inlet valve as well. The valve has two solenoids, one for the water valve and one for the ice maker. If the valve is not working it will not send the water up to the ice maker. You can test all of these parts with a multimeter. Good luck with your repair.

Related Parts: Water Inlet Valve, Icemaker
1 person found this helpful.

Most Recent

Question:

Ice maker will not stop making ice, even with the switch on off

kGary Meisner for model number Ksrg25fkss02
Answer:

Hello Gary, thank you for contacting us. That sounds like it would be the emitter and receiver boards. They control the ice maker functions. You may want to see about replacing that part. Good luck with the repair!

Question:

I have replaced the ice maker in which the seal was bad and the emitter boards the led is blinking twice pause then blinking twice again. When i hold in the door it keeps the same blinking pattern. When i hold in the freezer light switch there is no led, what can be wrong?

Pam Hull for model number MSD2669KEA00
Answer:

Hi Pam, Thank you for your inquiry. You may have to check the connections to the control board and the control board itself to see what is causing the issue. I hope this helps. Thank you and have a great day!

Question:

Where is the water inlet valve located and how is it tested?

Brian for model number KSRL25FXMS00
Answer:

Hi Brian, Thank you for the question. The valve is located on the back of the appliance where the water line from your home plugs into the appliance. In order to test the valve you will need a Ohm meter to check for continuity. Hope this helps!

Question:

Ice maker quit working, so I replaced it. Makes ice but will not eject it. Could the problem be the emitter and receiver boards?

Bruce for model number GS5SHAXNL00
Answer:

Hi Bruce, Thank you for the question. These boards tells the ice maker when it's full and that it has to dump the ice, and it also tells the ice maker when to refill with water, so I do not think it would be the boards. I suggest checking to see if the Auger is turning in the ice bucket and pushing the ice out. Also check to see if the ice door is opening and not stuck or frozen closed. Hope this helps!

1 person found this helpful.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 73 reviews What's this?
1-15 of 73
 

181 of 203 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Vince from El Cajon, CA

Ice maker would not stop making ice.

First, I tested the ice maker "switch" that actually just covers the beam that regulates the ice maker. In the "off" position, it still made ice. Then, I removed the three screws on the cover over the transmitter and disconnected the circuit board at the wire connector. It stopped. After ordering and receiving the new transmitter and receiver boards, I replaced both boards. They are located on either side of the freezer compartment under panels held in place by three screws. Probably saved 150 to 200 bucks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

67 of 80 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: RICHARD T. from PATERSON, NJ

Ice maker just stopped working..

Did the diagnostics with the blinking light and couldn't decide what was bad....so ordered the control boards and the module motor assm. also. Turned out that it was the control boards and would suggest that future customers order that part first...if it isn't that then get the module and motor assm......these guys ship really fast and the prices are literally half of what Sears would charge, not to also mention the cost of their service man to walk through your door...OUCH!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

62 of 67 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Riverside, CA

Ice maker stopped making ice.

I first removed the power cord of the refrigerator from the receptacle. I then removed the screws (3 each) from both the emitter and receiver face plates with a phillips screw driver. I than carefully removed the connector to the each of the circuit boards. A simple pull maneuver. I removed the circuit boards from the face plates. I took the new parts and put them back in reverse order. I put the power cord back in the receptacle.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

39 of 41 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Gerald from Fulton, KY

Ice maker quit making ice

While looking for parts I read the advice on you web site under the ice maker parts. I also had problems reading the LED codes. They would change each time I unplugged the refrig and powered up. I took the other guys advice, ordered the emittered and receiver and the next morning I had ice. GREAT service guys, thanks. Also the part was on my door step in 1.5 days. Sure beat an expensive service charge.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

32 of 34 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Robert E. from Payson, UT

The ice maker stopped producing ice.

If you remove the bottom vent panel of the refrigerator there are two schematics for the refrigerator. One for the fridge and one for the icemaker. The icemaker has an emitter and a receiver that will tell the icemaker when it is ok to dump ice and add water. The receiver has an LED that blinks different codes. The codes give you an idea where your problem is located. In my case it coded out to be the optics (emitter and receiver). Replacement of the parts involves the removal of three screws on each component and disconnecting a wire harness on each component. Install the new components by following the removal process in reverse. The total cost was $80.00. This was half the price Sears wanted for the parts and about the same price to have a Sears repairman just show up at the house.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

25 of 26 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Glenn from San Marcos, CA

My ice maker stopped producing ice. It would dispense ice that was already made and the water dispenser worked.

I looked at some online diagnostics info and the owner's manual. The "error code" blinking red light on the receiver unit (located adjacent to the ice bucket) indicated that the emitter/receiver units were faulty. I located the parts on the PartSelect website (their price was less than half of what they wanted on the Sears website) and ordered them. I didn't pay for the expedited shipping and still received the parts within two days of ordering. Powered down the refrigerator, three simple screws to remove each cover for the emitter and receiver, unplug the old units and pop in the new units, replace the covers for each unit, repowered the fridge and, voila, you've got ice. I completed the repairs in less than 10 minutes. Couldn't be happier with the price, the diagnostics links/info or the prompt service. Next time I have an appliance issue, my first stop will be this website.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 25 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Lisa from Stuart, FL

Ice maker not working

Well I changed out the optical boards which I thought were the problem and the ice maker is still not making any ice. I can see the ice makers fingers rotating but there is no water entering through the tube. I jumped the water manifold in the back and water comes out but I cant figure out what is not telling it to run water and fill the ice tray. Any ideas would be appreciated I guess i'll replace the ice maker next. Thanks in advance.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 15 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Matthew from Austin, TX

Ice maker stopped producing ice

Emiter blinking red; ice maker stopped working. Called appliance repair, said electronic control boards needed to be replaced. Quoted me $275, including parts. Ordered part at partselect.com, installed in 15 min and ice maker started producing ice. Also discovered on other online forums that this part is a common failure on these model refrigerators. Very easy to swap out, plug & play. Make sure to unplug appliance before performing repair due to shock risk.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 15 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: James from Satellite Beach, FL

Ice maker would not stop making ice (style 2)

Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.

Biggest problem was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

38 of 88 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: michael from gurnee, IL

No ice

I installed a new icemaker and ice level sensors I also had to replace crummy plastic trim parts because of poor quality and broke during disassembly

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 9 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kyle from Severna Park, MD

Ice maker stopped working

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 9 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Katherine from Pittsboro, NC

The ice maker was not making ice.

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 13 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Johnathanh from Portland, OR

Ice maker would not dispense ice

Light was blinking on the Electronic Control Boards. Ordered replacement (emitter and receiver)and installed, and now it's working.
Some note: 1 year ago, the board started to blinks (meaning it's bad) but it was still making ice. This gave me a false error when it really failed, took the risk and ordered the replacement parts and all is well now.

One more thing to pay attention to , and it may only be on my model of refrigerator, but the wires harness that connect to the receiver board (big board) have large and stiff wire. With limited space where the board and the wire are seat at, it put lots of pressure on the pressure on the board's connector. This pressure, over time, will cause the right angle connector's solders to crack and may be a contributor to the failure. If you're installing the new board, try to re-inforce the connector with some rubber heat glue and also relieve pressure from the connector's end, which I hope will prolong your board.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 10 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Travis from Normal, IL

Ice maker stopped working

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 8 people found this instruction helpful

Parts Used:
  • Emitter and Receiver Boards
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: David from Hermitage, TN

Ice maker had stopped making ice.

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 73

Model Cross Reference

This part works with the following models:

PartSelect Number: PS10064583
Manufacturer Part Number: W10757851
Brand Model Number Description
Kenmore10641522500Refrigerator
Kenmore10641523500Refrigerator
Kenmore10641524500Refrigerator
Kenmore10641529500Refrigerator
Kenmore10644022600Refrigerator
Kenmore10644022601Refrigerator
Kenmore10644022602Refrigerator
Kenmore10644022603Refrigerator
Kenmore10644023600Refrigerator
Kenmore10644023601Refrigerator
Kenmore10644023602Refrigerator
Kenmore10644023603Refrigerator
Kenmore10644024600Refrigerator
Kenmore10644029600Refrigerator
Kenmore10644029601Refrigerator
Kenmore10644029602Refrigerator
Kenmore10644029603Refrigerator
Kenmore10644032600Refrigerator
Kenmore10644032601Refrigerator
Kenmore10644032602Refrigerator
Kenmore10644032603Refrigerator
Kenmore10644033600Refrigerator
Kenmore10644033601Refrigerator
Kenmore10644033602Refrigerator
Kenmore10644033603Refrigerator
Kenmore10644034600Refrigerator
Kenmore10644039600Refrigerator
Kenmore10644039601Refrigerator
Kenmore10644039602Refrigerator
Kenmore10644039603Refrigerator