Quick Question!

Have you ever purchased from PartSelect.com before?

10064572-1-S-Whirlpool-W10756692-Electronic Control Board
10064572-1-S-Whirlpool-W10756692-Electronic Control Board 10064572-2-S-Whirlpool-W10756692-Electronic Control Board 10064572-3-S-Whirlpool-W10756692-Electronic Control Board https://partselectcom.azureedge.net/Schematics/Maytag/OSFPJUUG.gif

Electronic Control Board

Your Price

$366.52
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS10064572
Manufacturer Part Number W10756692
Manufactured by Whirlpool

This part helps with the tumble and spin cycle. If your motor won't run in either the wash or rinse cycle or if the fuse on the board is blown, then you have to replace this part. The fuse is not sold separately. NOTE: Motor is sold separately.

This part works with the following brands: Kenmore, Whirlpool, KitchenAid, Maytag.

This part works with the following products: Washer.

This part fixes the following symptoms:

  • Pumps but will not spin.
  • Will Not Start.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Washer had door lock error code. I already installed a new door lock assembly and it did not fix the problem. When i attempt to start the machine, i do hear, although faintly, the six clicks that the machine makes while attempting to lock the door. Does this mean that the problem is in the control board? I'd like to find out before buying one and attempting to install it. Are there any other possibilities i should rule out first? Thank you!

Lisa for model number ghw9460pw1
Answer:

Hi Lisa, Thank you for your inquiry. To verify if the electronic control board is causing the issue, I would test it with a multimeter to check the continuity on it. If it is not causing the issue some other parts you may have to check are the door hook/strike, the temperature sensor, the hold to start button, the door handle, the flowmeter, the drive belt and the control knob. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Most Recent

Question:

When I turn my control switch from normal to heavy duty the quick wash lights up. The washer works fine in normal mode but will not go into heavy duty or sanitary.

Jim for model number ghw9200lw
Answer:

Hi Jim, Thank you for the question.This sounds like there us an issue with the Electronic Control Board. The board is not repairable so it will need to be replaced. Hope this helps!

Question:

My machine will not start. It shows error code FdL and makes clicking noise in back of machine.

Ronald for model number GHW9150PW0
Answer:

Hello Ronald, Thanks for your question. It is possible the door lock mechanism (part number PS11745016) is broken or removed, or the door lock unit (part number PS11744910) has failed. Disconnect power and unplug unit to check door switch/lock unit. Check the wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. Note that the unit will attempt to lock itself during this error six times before displaying the error code. I hope this helps.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 3 reviews What's this?
1-3 of 3
 

79 of 88 people found this instruction helpful

Parts Used:
  • Electronic Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Bradley from Red Wing, MN

My washer would not always finsh the cycle (most of the time it would run between 2 and 30 minutes) and then the time display would flash and the washer would shut down and beep. An f06 fault code flashed in the display.

First I removed the screws and the plastic slide clips to remove the back plate. I then went to the lower right of the washer and found the motor control unit. It has about four plus going into it. The front inside mount of the control unit has a clip on it that must be pushed so you can pull the unit free of the bottom of the machine. Once the control unit was free I flipped open the plug cover with a screwdriver which just snaps over the plugs. I then removed the plugs from the unit carefully so I didn't break them. It was a tight work space and I had to pop out some of the clips that hold the wire harness in place to get some slack in the wires. I then pushed up on the washing drum which gave me enough room to slide to old unit out and get the new one in. Then just reconnect the plugs, plug cover, snap the unit back into place, refit and wire harness clips that where removed, and place the back panel of the machine back on. I tested mine before putting the back panel on and it completely solved the problem. Note that there are 2 control units in this machine 1. motor control and 2. the central control located behind the display. I was told it could have been either one of them, but after some research I chose the motor control unit since it seemed to be a problem with the tachometer sensor which is read through the motor control unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

22 of 31 people found this instruction helpful

Parts Used:
  • Electronic Control Board
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Christina from Englewood, FL

Error f 11. Mashine would not run

removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 25 people found this instruction helpful

Parts Used:
  • Electronic Control Board
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Brent from Normandy Park, WA

Motor control board faulted.

I read the instructions once and then started. It was easy but did take an hour to do the entire job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS10064572
Manufacturer Part Number: W10756692
Brand Model Number Description
Kenmore11042822200Washer
Kenmore11042822201Washer
Kenmore11042822202Washer
Kenmore11042822203Washer
Kenmore11042824200Washer
Kenmore11042824201Washer
Kenmore11042824202Washer
Kenmore11042824203Washer
Kenmore11042826200Washer
Kenmore11042826201Washer
Kenmore11042832200Washer
Kenmore11042832201Washer - Kenmore Washing Machine
Kenmore11042834200Washer
Kenmore11042834201Washer
Kenmore11042836200Washer
Kenmore11042836201Washer
Kenmore11042922200Washer
Kenmore11042922201Washer
Kenmore11042922202Washer
Kenmore11042922203Washer
Kenmore11042924200Washer - Kenmore Washing Machine
Kenmore11042924201Washer
Kenmore11042924202Washer
Kenmore11042924203Washer
Kenmore11042926200Washer
Kenmore11042926201Washer
Kenmore11042926202Washer
Kenmore11042926203Washer
Kenmore11042932200Washer
Kenmore11042934200Washer