ZRT6510WW (P1143444NWW) Amana Range - Instructions

The front burner the large one was burnt out, I cook alot so I need it, I happen to see a appliance repair man next door. I describe problem and he said well figure about 250 - 300 hundred dollars. 80 For the aprt the rest labor and house call. Well I looked at the booklet and figured out what I had to do ,needless to say I owent to your website and you had the exact part I needed and saved me alot of money. I sugest to d. I. Yers try it and if it doesn't work then call the repairman. Thank you parts select. Glenn voight

Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Indicators showed broiler should be working so basically made a guess that the element was bad and replaced it. Turned off circuit breaker and removed mounting screw and unplugged terminal ends of the element and replaced with new one. Switched circuit breaker on and turned on broiler and my repair was a success.

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

Remove three strews and two wires. Less than fifteen minutes for this Seventy Seven year old farm boy!

Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.

Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.