ZEM200SF02 General Electric Microwave - Instructions

The microwave had been working fine until one day when the timer counted down but the heating motor (or whatever you call it) would not come on. So the timer would count down but nothing inside would get hot. I did not know what it was for sure but decided to take it apart and look. Once I had the control panal off, I found three small wired switches inside. One of these switches appeared to have shorted out. So I searched online and found Partselect.com. I found a matching switch , ordered it (arrived in couple days), put it in, and VOILA it works! Thanks Partselect.com.

I've been fixing and taking things apart since I was a kid. I hoped that it was a bad switch in the door. Got out my test meter and check the 3 different switches. All 3 tested good, but one was a bit hit and miss. It would work if the microwave was on its side and wouldn't when it was set flat. I found the switch online and installed it. Took care of the problem.It was a whole lot cheaper than buying a new microwave. Thanks! Bill Brown, Fridley, MN

Fortunately, my brother-in-law suggested it might be the "cut out" switch. After unplugging the microwave, I opened it up and identified one of two cut outs and removed the wires from each side of the cut out. To test if that was the problem, I connected the two wires together, bypassing the cut out. When I plugged the unit back into the wall socket, the lights came back on, and i ran the microwave for a few seconds. It verified that this was the problem. I ordered the part and when it arrived, I removed it with a philips screw driver and replaced it with the new one. I replaced the screw, buttoned the unit back up, plugged it in, and saved a few hundred bucks on a replacement microwave, and as important, saved our landfills and planet a tiny but.

The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

Took the cabinet off the microwave and checked for a fuse. Found that it was good, then checked for the voltage path to the controls and found the cavity thermal cut out was not conducting. Using a voltage meter to check things. Unplug the microwave for several of the tests. You must know how to work with electricity to do this. Installed the new part and the microwave now works. As a hint to what had happened my wife had heated a large casserole then right after that went to heat a smaller dish. At that time the microwave was hot and did not restart.

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Per the troubleshooting diagram inside the microwave oven, I discovered the one of the TCO was open (using Ohmmeter). Found my microwave oven model on PartSelect and used the diagram to select the TCO needed and placed order. Part came in three days, installed new TCO, reconnected wires and the microwave oven was back working in 10 minutes.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

must of had loose connection from wire terminal
to thermostat from factory. thermostat and wires
were melted. removed thermostat. and cut burnt
wires back. replaced thermostat and terminals.
used better quality terminals than factory.
also checked and tightened other loose connections. there was enough wire left after cut back to just put on new terminals.

took of cover removed switch and replaced with new one

Took the cover off (removed the five screws, two of which were security screws off the back) and found one connector on the thermal cut out with its shielding melted. Very easy swap out of the new cut out and we were up and running as if new.

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.