ZEM200SF01 General Electric Microwave - Instructions

I had a bad cut off sensor on oven cavity I ran the Microwave with nothing in it and it smoked I ran it for another 6 months then 1 day I was heating water and it stop- working. I put a new tube in might be Okay but I was not going to risk it taking another cut off sensor on overload. You have to change sensor and put on a new tube. Clearly it would be cheaper to buy a new unit but it was only 2 years old and I am an old tech and was curious. The sensor cost only 16 bucks new tube about 55 a replace brand new oven 81 bucks there you have it I was stubborn and going to get that sucker back into operation I had another oven go out the same way

20 month old GE m/w had made "electrical" smells from beginning. Finally unit failed to turn on. Disassembly was easy except that I needed to buy anti-tamper screw driver bits from Sears to remove two screws. Found the blade connector to the sensor was a loose fit, resulting in severe heating at the connection. Plastic connector was melted and sensor was damaged to the extent this seems a possible fire hazard. Replacing the sensor is trivial, and requires removing one Phillips head screw. Reterminating the defective connector requires basic electrical skills; wire stripping and crimping. Be sure to clip a few millimeters of wire to get undamaged copper. Be sure to replace both connectors if connections feel at all loose. M/w reassembly is trivial.

I googled "Microwave stopped working", and after reviewing numerous websites with suggestions, I found the response noted below at "Help Owl" which was the most straighfoward and clear explanation to trouble shoot the problem. I first tested the Thermal Cut Out (TCO) per the instructions below and that was the problem. I didn't have to test the electrical fuse. Turns out that you cannot typically use the microwave continuously for more the 12 or 13 minutes or it may overheat and the TCO will shut it down. Extremely easy to test for and fix, and the part is only $15! See Trouble Shooting steps as follows: Make sure that the unit is vented properly and that if you are using it for prolonged periods while cooking, that you turn-on the vent fan.
If there is no display / power within the unit...first check your power source where you plug the unit into the wall.

If that is good, Remove the Cabinette/Cover "Note: it has 3-Torx Anti-Tamper Screws".

Then as you face the microwave from the rear, at the left rear corner is a small circuit board with a fuse. "Check the Fuse"

If the fuse is good, Check the following:

1 - The most common component failure is the "Cabinette TCO" (Thermal Cut-Off Thermostat).

As you face the microwave from the rear...It is located under the cover, on top, on the left front corner area.

It is a Circular, Black & Silver Disc Shaped component about the size of a dime in diameter and is about 1/2" in height.

It has Two (2) Wires attached to it's spade connectors and it acts as a safety fuse.

"IF YOU PUT AN INSULATED JUMPER WIRE ACROSS THE 2 TERMINALS THE POWER SHOULD RETURN AND THE DISPLAY WILL LIGHT"

Anything other than these two items should be checked by an Authorized Service Technician as these microwaves have components thay carry "HIGH VOLTAGE SHOCK HAZZARDS"

I opened the box, took the turntable guide out and put it under the microwave plate.

It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.

Remove cover-the hardest part, as I needed to buy a new set of driver bits that included the dimpled security drivers to remove three screws. GE includes schematic and troubleshooting flow chart with the unit, taped inside the cover. Required more time to look up the part on-line and order it than time used to make the repair.

Remove the microwave cover. Requires a phillips screwdriver and a torx security bit/nut driver (there are two security type screws on the back...guess they don't want you to do this at home!). I had to buy the a security bit set (about $7). The diode is easily accessible on the right side under the fan. Requires removing on small phillips screw and unplugging on electrical connection. GE provides some instructions in an envelope on top (after cover removed). There is a warning/instruction to discharge the capacitor before service. This was not a problem for me. Actual diode replacement took 30 seconds. Whole job = 15 minutes.

I removed the cover this required a special star Apex tip witha hole in the center. $10 for a set at Lowes.Replaced the fuse and Thermal cut out at the same time. The oven woks like a charm.I would like to add that GE customer service was no help basically told me that it was a throw away unit. If they built it you can fix it.Hope this helps any DIY breathern outthere.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

I took instant pictures at each step to make sure I put the wires back correctly. Removed the front panel. Discharged the capacitor with a voltage meter. Removed parts in front of the magnetron. Removed and replaced the magnetron. Reassembled. Works find now. Small hands, a flashlight and a magnet (for dropped screws) would help. I did not need the pictures.

removed access panal, found soft switch as discribed on your web site. removed and replaced.

I slipped the new saucer out of the box and placed it in the microwave. I was very disappointed to discover that the new one didn't fly like the old one.

Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.

New part came -- perfect fit, set it in the microwave, no problem.

thank you very much.