ZEK757BA3BB General Electric Wall Oven - Instructions

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

1. Turn breaker off at breaker box. 2.Disconnect old broil element. Pull electric wires out 3-4 inches from BACK of oven. Clamp wires or tie off so they do not retreat behind back oven wall. INSTALL wires to new element and secure back plate. Install NEW clamps to new element. Switch on breaker and check operation.

Be sure to flip the breaker to the oven to the OFF position before doing anything. Take out the two screws at the back of the oven that hold the element. Carefully pull the element forewarn to expose the connections to the wires. Disconnect the element from the wiring connectors. Be careful not to damage the connectors or the wiring. Plug the new element into the wiring connectors. Make sure you have the connections firmly in place. Push the wiring and connectors back into place. Replace the two screws. Make sure the element is resting in the spacers that keep it the correct distance from the top of the oven. Flip the breaker to the ON position, Turn the oven on Broil. The element should start turning a bright red. some fumes will come off the element. That is just oil from processing and handling. Your done!

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

switched off power to oven, unscrewed old broiling unit and installed new one.

Followed the instructions

By myself

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

This part is a plug-in unit - two screws off; unplug the old unit; plug in the new unit; two screws on. Very simple.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

Replaced it

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

I thought because the broiler was off that I could remove the element with not problem. As I was pulling the element out, it sparked, melting something in the back I couldn't see at the time. I immediately went to the breaker box and turned the power to the oven off. After I found the website online I was very gratified to see how easy it was to identify the element I needed and order it. I removed the old element. One of the wires from the element slipped through the hole in the back of the oven. To get at it I had to unscrew the four screws around the outside edge of the oven and pull the whole oven out. I had a table handy that I pulled up next to the oven and set it on without disconnecting the main wiring. After getting the oven out I removed the six or so screws on the coverplate and easily found the loose wire. I pushed the wire back through the hole in the back of the oven and made sure it would not fall back into the hole. I put the back plate on with all its screws; pushed the oven back into its hole and screwed the four screws in around the edge that hold the oven in. Then I attatched the broiler element to the spade connectors and screwed it back in place. I turned the breaker switch back on and tested it. It works.