ZEK756GP3BG General Electric Wall Oven - Instructions

Removed the oven racks, removed screws holding element hanging support from roof of oven, removed screws holding plate of element to rear of oven. CAREFULLY worked element loose from back of oven and gently alternated pulling each side of element (near the base) until connecting wires came free of insulating batting. Pull too hard and the connecting wires can break loose and disappear behind the batting. Once freed, disconnected both wires with socket (use pliers for extra grip on flat part of connectors, if necessary), removed element, braced new element on bottom of oven, aligning connectors to now-free wires. Re-attached with the new screws that came with the element (attachment points on element are threaded; do not reuse old screws as the threads may not match), gently re-inserted element into insulating batting at rear of oven, reattached hanging support, then replaced element plate screws.

Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.

It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.

Snapped in the clip

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

It was very simple.. first turn off the electricity... next take out the two screws holding the element to the back of the oven... then pull the two plugs apart( male and female ends) ... throw away old part.
put new part in by plugging the male and female ends back together... push back into oven back.. get all insulation back in... put two old screws back in to secure... done.. turn on power...
don't be afraid.. it was very, very easy.

Remove the screws inside the oven holding the back of the element to the rear wall of the oven. These scrrews are a square drive. Pull element forward and remove 2 screws that hold wires in place. Both sets of screws needed to be replaced with a different size. Reverse order to install.

The two dollar socket set from Xmas 20 years ago had the right size socket..

Long arms are advisable.

The lower element still plugged in while the upper wires were just hanging there surrounded with fluffy white insulation fuzz, I wondered, " Could I bake a potato for my yearning and hungry family?"

When I explained the situation to my retired father in Arizona he said simply, "I wouldn't."

The new element popped in. It got really red, and, kinda like watching my toaster toast, the show was pretty much over after it heated up.

Shalom and Merry Christmas Folks!

I first removed the broken element by removing the two hexhead screws on either side of the element bracket. Then I gently pulled the wires through the opening and removed two more screws that attached the wiring to the element. I then compared the new and old elements and found a few differences.

First, the screw holes where the wires connect to the element were tiny in the new element, about a third the size of the holes in the old one. Secondly, the mounting bracket was not as long as the original, and the holes to mount it to the back of the oven are located at the top of the bracket, instead of the sides.

Since this was the only element that I have found, that comes close to the original, I decided to make it work.

I took my drill and a small bit and bored out the screw holes, just enough to get a self taping screw to fit and reconnected the wires.

Now I'm not sure that I would recomment the next step to anyone, but I did this: I held the new bracket against the back of the oven and drilled new holes to match the new bracket, and again used self tapping screws. The reason that I don't encourage this is that the new bracket fits just inside of the old opening, but the insulation cannot be seen as long as the element does not get moved. I then plugged the original bracket holes with the original hex head screws.

It took a little more time and effort than I had expected, but well worth it, after eight months without the use of my oven.

Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D

It's so simple most people could mannage the repair. Turn oven off. Remove oven door and shelves. Use a nut driver to remove mounting screws. Pliers to pull quick connect terminated wires off element terminals. Use pliers to push connectors onto new element,wires may connect to either terminal. Nut driver for screws to mechanically mount new element. Replace shelves and door. First time element gets hot it will burn off oils and dirt, not a problem but do it now not later.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

Removed burned out element and discovered replacement element had a different back plate and different hole pattern. Also, the electical connecttion from power wires to ends of element were a TOTALLY different size, both in hole size and size of material that hole was placed. This tood a lot of slow increasing the size of the hole time. Also, the backplate was a different size with a two hole pattern at the top of the plate, as oppossed to the original plate with holes centered at the sides of the plate. Had to drill holes in back oven wall higher than I wanted, as the oven wall had a depression in the back wall and I could not drill at that point. By drilling holes that were higher than previous holes, there was now a 1/2" opening at the bottom of this plate. Used a hack saw and cut off a piece of the old plate to slip underneath, then screwed in the new plate, thus filling the remaining opening, and securing the additional hand made additional plate. This was a lot more than I had bargain for, and when I turned on the oven, it did not work! I re-checked the connection of the power wires to the grid element and found one of the connections to be disconnected. Reconnected this wire and everything is just ducky now.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping

[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.