Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YWED94HEXR2

YWED94HEXR2 Whirlpool Dryer - Overview

Get Parts and Repair Help for YWED94HEXR2

If you know the dryer repair part you need, you can browse the list of all parts on the YWED94HEXR2, or you can search by name or part description. You can also find your part by where it is located on the YWED94HEXR2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YWED94HEXR2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

$20.42

Idler Pulley

The idler pulley with tri-ring and gasket, also known as a dryer belt tension pulley wheel, is used in dryers. This part maintains the right amount of tension for the belt to rotate the drum. This effectively spins the drum. If your dryer is experiencing any of the following symptoms, it is best to replace this part: not rotating, does not start, making squealing noises when it is in use, or it does not tumble properly. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions.

$42.43

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$13.09

Drive Belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

$10.34

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this pa...

$21.40

Thermostat, Internal-Bias

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...

$4.94

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$41.80

High Limit Thermostat and Thermal Fuse Kit

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a hig...

$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2149 of 2417 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 668 of 700 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more

Dryer overheated, blew out thermal fuse

  • Customer: Steven from East Norriton, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set
  • 293 of 335 people found this instruction helpful
I started to repair this and got busy and ended up calling a repair service -- that was the first time. They repaired it for over $200 and said the cause was bad venting. I fixed the vent before using the fixed dryer but it blew again. So I ordered these parts and replaced them myself for a lot of savings. However, the dryer still overheated. Through lo... read more