YE20FA4C Magic Chef Dryer - Instructions

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.

Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.

I took the front off the cabinet (pry up front of top and remove two screws. Removed the drum, replaced the left rear drum support roller by removing one snap ring on shaft of roller and repacing after installing the new wheel. Reinstalled the drum, the hardest part of the repair was getting the belt back on the drum. It is hard to reach the belt to place it back on the motor. (small space to reach through) Being able to purchase a single wheel from this website saved me $50.00, the local suppier wanted to sell me a whole kit.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

1.Removed retaining clips,washers,spacer,and cylinder rollers
2.Removed and replaced support assembly
3.Installed spacer
4.Installed cylinder roller assembly
5.Installed washers and retaining clips
This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.

watched your video on 'how to' and did it like man showed..no problem

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Looked up dryer by serial number on the internet. Watched the video on the website very easy installation. Ordered the part it came in within 2 days. Opened the top of the dryer with a 10 in one tool (like a putty knife). Took out the out defective parts by unscrewing the thermostat took wires off the old part and put them on the new part not to confuse wires. Did the same with the heater element installed the new parts. Very simple. If I had to call a repair person it would have cost 3 times as much as the part alone.

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Learned as I went along, from various YouTube videos.

I lucked out opening the top of the dryer in that I didn't break anything when I popped the top up, since I didn't know to use a putty knife to depress inward the retaining clips.

Found the belt lying on top of the drum, and when I lifted it, it easily came free since it was broken.

Watched the YouTube from PartSelect, finally, and Steve made it seem so easy. Unplugged it, turned off the gas, too.

Front two screws unscrewed no problem. Front panel lifted away, no problem. Tons of lint in the front housing, so I decided to clean away as much lint as possible since this was the best opportunity, and I also vacuumed lint out of the sheet metal exhaust all the way to the outdoors exit port. Then I had to get that sheet metal pipe back in place, perfectly, and that was a little tricky

The roller kit was a bargain compared to separate parts I thought I'd need (one roller only) so I replaced both rollers and their posts, spacer, and washers.

Another vender video recommended high temp lithium grease to lube the new posts, but I just used "plumbers grease" that I happened to find lying around the house.

The most difficult part of the whole process was pre-fitting the new screws into the plates of the new posts because you are self-threading the screws and I didn't have a nut driver. (I was trying to do it using two wrenches, one to hold the plate, the other to turn the screw. The torque required is so high that you'll start to round the hex edges of the screws and ruin them. So, I went out and bought a 5/16" socket for $2.49, and self threaded the screws by holding the plates with a wrench, and using my power drill with the 5/16" socket.

This is where you risk ruining everything because as soon as the screw has self-threaded the plate, the resistance drops to near-zero, and the drill zooms the screw down hard onto the plate. I found, afterward, one ribbon of thread lying on the work area, which means I stripped one of the threads by one winding. (I'm not too worried, but it did make me wonder if I had screwed up. Keep the old screws to use as replacements for the new ones if you encounter the same problem where you inadvertently strip a screw too far.)

Then, the plates go back into the dryer, and the left side plate has a much larger gap, because you have to remove/replace it through the rear wall slot by turning it in-situ; the right one just falls down into your waiting hand, and is replaced by raising it up from behind its slot.

Finally, you come to the belt replacement, and just follow the way Steve showed in the YouTube. However, I tried and tried, but it was difficult for me since I'm left handed and you do it with the right hand. I was finally able to get it by getting the belt around the metal drive, first, and then bringing the white wheel over and working it into position by pulling the belt forward to clear the white wheel being positioned to receive the belt's tension.

This is a very doable dryer repair, it will save you hundreds of dollars, you'll do a better job than a repairman (since you vacuum all the lint out too), and its a great story to tell your friends.

Learning how to do it, actually doing the repair, and then double checking that I got everything "right," I'd guess that I put in 8 hours of my time.

It was fun… but keep your cool since there will be a little aggravation, and maybe a trip to the hardware store to get tools you don't own.

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.