XRSS267BW (PXRSS267BW0) Amana Refrigerator - Instructions

Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.

By sliding the drawer out and lifting it up at the end, the drawer will come right out. By installing the new drawer in the same sequence, the job is completed. As for the filter, it is located inside the refrigerator compartment on the upper right side.Simply remove any items from the top shelf that may be in the way, and then push in on the tab that extends out from the filter housing. The filter and connector will swivel down at that point,simply hold the connector in one hand to stablize and with the other hand, twist the filter counter-clockwise to remove the filter. To reinstall the new filter, remove all protective covering from filter. Plase filter against filter connector and turn until tight (1/4-1/2 turn).Raise complete assemble upwads until tab snaps back into place. Installation is now complete, next purge the air out from water supply by placing a pitcher or other large container under the dispenser and activate.Run water for a minute or so until all air is removed.

I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!

The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!

I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer

After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts.
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.

unscrewed to removed old and screwed in new

Piece of cake!

Removed the old ice bucket which was cracked and ice would not dispense. The Helix Cap also looked worn which is why I ordered both parts. (Probably if not for the shaking of the ice bucket the Helix cap would have been the only part required. We ended up cracking the ice bucket) Removed the four hex screws from the auger system on the old ice bucket with a socket wrench. Removed the old Helix end cap from the auger system and replaced with the new. Literally just slips on the auger. Reinstalled auger system back onto the new ice bucket. Total time not even five minutes.

Working great! Probably saved $ 75.00 - $ 100.00 on a service call. Half of a wrench on skill level needed (One=Low skill level/ Five=High skill level)

Great response & delivery from Parts Select!
Definitely recommend highly.

Todd
Lancaster-PA

The parts discription was a bit vague and I wasn't sure exactly what I was ordering, but I received everything I needed and it works fine. The combination screw conveyor/ice crusher came in one piece. The ice cube bin is a plastic assembly that snaps apart. I used a wide blade screw driver carefully to facilitate assembly/disassembly. Once you have it apart the old converyor slips out and the new one slides in. Do not remove the two screws that hold the new assembly together. You need a phillips scredriver to take out two of the screws from the old assembly and put in the new one. That is, there are four screws and you need to trasfer two of them. Everything now works fine.

Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

remove top plastic cover / phillips screw driver
remove top door bracket / 5/15" socket
lift off door
remove pieces of old cam / phillips screw driver
replace cam/ phillips screw driver
replace door
replace top bracket / 5/16" socket
check alignment

Turned old one until it snapped out. Replaced it with a turn.

This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simple on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering.

I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

The part that actually moved the ice in the bucket itself kept slipping off the ice bucket in the refrigerator. This was causing ice not to be dispensed. It turned out to be a screw hole that was stripped and was not tight enough to keep the part in place to work properly. I just took it apart and replaced the bucket, put the screw back in and within 10 minutes we were done. I also ordered a new drawer that was broken for the deli meats. I know this was caused by my 6 year old daughter not closing the drawer correctly and the front door getting closed on it. I will have to say when I first came to the site to place my order I thought I was going to have to pay alot more than I did for the parts. The pictures were a great help in finding exactly what I needed. The order was received in great condition and very fast. I will be ordering from you again in the future if I ever need anything else repaired. Thanks for helping a women be independant and fix her own repairs.