Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWTR1502KW0 > Instructions

WWTR1502KW0 Crosley Refrigerator - Instructions

All installation instructions for WWTR1502KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWTR1502KW0
121-135 of 212
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator section not cooling

  • Customer: Anant from Stone Mountain, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked defrost timer. It was a shocker: it was completely burnt out. Replaced it with the new part very easily. I thought now it would defrost properly but unfortunately the thermostat also was shot. I had ordered it along with the timer just in case. It was not expensive at all and I saved time but having it with me when I replaced the timer. NOW ALL IS WELL AND REFRIGERATOR SECTION COLLING PROPERLY. THANKS TO VIDEO AND PARTSELECT.

Frig Section Too Warm,Freezer Ok

  • Customer: LANCE from AURORA, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Using your online troubleshooter, it was probably the defrost timer and/or the defrost thermostat. Both cheap so I ordered both. The online repair videos showed how to replace those parts. Replaced the timer first with no problems. Removed the panel at the freezer back an saw a streak of black smoke on the white panel wall above the thermostat. Good chance this was the failure point. Video also showed how to replace this unit without any problem. Set the temperature control and let the frig run over night. Problem solved!frig at 38d and freezer at 0d.

Refrigerator was not cooling

  • Customer: Scott from Norman, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

Replace the handle mount

  • Customer: RUTH from AUSTIN, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When I was moving the refrig. handles from one side to the other...I broke one of the mounts. It was SO easy to order from this place, and they ship IMMEDIATELY. Second time I have used them, and am VERY impressed.

no heat when drying

  • Customer: Glen from North Tonawanda, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced thermo-fuse

Rental house, fridge door handle broke off and renters threw it away.

  • Customer: Peggy from Wellington, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the handle from Part Select, waited a couple days and it came in the mail. Husband took it to the rental and replaced the handle. Very easy process from beginning to end. Have put Part Select in our favorites to keep. Thank you so much for this service and the ease of the process.

It would freeze up or not cool at all, depended where the clock stopped.

  • Customer: Roger from Owatonna, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

fridge not cold stays running

  • Customer: Joseph from Deland, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Refrig would not defrost

  • Customer: Robert from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Diagnosis: used wiring diagram attached to frig and determined cause could be wiring, heater element, thermostat or timer. After completely defrosting the frig (turned it off) I removed the rear cover in the freezer and looked for an obvious problem. None seen. Removed temperature select pod from the frig box and looked for obvious problems. None seen but defrost timer appeared poorly made. Repair: Since I had no practical way of checking the defrost cycle in operation, I checked probable failures on the Part Select website and saw defrost timer as most probable. I ordered the timer. Installed it. Waited a few days to make sure the frig went through a few defrost cycles then removed the freezer rear cover. There was no excessive frost buildup so I'm reasonably sure the repair was successful.

Cover (shelf) that holds the hydrators was cracked.

  • Customer: Mary Lou from Myrtle Beach, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Went on line to PartSelect, found and ordered the part. It was here in two days. I removed the old shelf, inserted the new and the frig was as good as new. I was extremely pleased with the ease in identifying the part and the speed of delivery.

Freezer and main compartment had wide temperature variations

  • Customer: Joseph from Tullahoma, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

The handle on the refrigerator had broken right off!

  • Customer: Stanley from Fonda, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the top of the handle that was still attached to the door and replaced it with the new handle and really made sure the bottom screw was tight and then positioned the top holes and screwed them into place. VERY EASY!!!

Broken refrigerator door handle.

  • Customer: Steve from Nashville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair literally takes 5 minutes...and that included 2 minutes to find my Phillips screwdriver. Save a ton of money, and do simple repairs like this yourself.

Refrigerator Ran Constantly, Was not Cooling as well.

  • Customer: Mark from Hertford, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Looked up troubleshooting info on your web site. Decided to replace the defrost timer. Ordered it using Paypal. Received the Shipment in about 1.5 days in Rural NC. Watched Your Video, cut off power to the fridge, removed the top self and unbolted the panel, removed the defective defrost timer, installed the new one and re-installed the panel and top shelf. Set the timer to defrost to check the operation (looked inside the freezer to see that the defroster was glowing red - it was) waited about twenty minutes to ensure that the fridge started cooling again. Fixed!

Freezer dripped water and items thawed but compressor ran.

  • Customer: James from Montross, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Instructions from partselect were very clear and probable cause made it easy to narrow things down. I have the manual for the refrigerator that shows the location of the defrost timer. Very surprised that it turned out to be a cheap and easy fix.
All Instructions for the WWTR1502KW0
121-135 of 212