Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWGF3004KWF

WWGF3004KWF Westinghouse Wall Oven - Overview

Get Parts and Repair Help for WWGF3004KWF

If you know the wall oven repair part you need, you can browse the list of all parts on the WWGF3004KWF, or you can search by name or part description. You can also find your part by where it is located on the WWGF3004KWF by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for WWGF3004KWF parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the WWGF3004KWF

[Viewing 6 of 6]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$33.65

PROBE,OVEN TEMP

The temperature sensor measures approximately 9 inches long. It sends the temperature up to the electronic control. Over time this can become weak and might be sending the wrong te...

$28.35

Natural Gas to Liquid Propane Conversion Kit

This kit is used to convert your appliance to liquid propane.

$23.65

Light Bulb Lens

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to...

$36.26

RACK

This part is found inside your oven. This oven rack comes in the color chrome and measures 24 inches in width and 16 inches in length. This is an extremely simple repair that requires no tools. The package you will receive will contain one rack. The rack may warp or become distressed over time and will need to be replaced. The rack is what holds your food inside the oven and allows you to adjust your food at different heights. Make sure your oven is unplugged before doing any maintenance. You will need to open the oven door and simply slide the new rack into place.

$8.93

Rear Drawer Glide

This rear drawer glide, also known as a storage drawer glide, is used in ranges. This helps hold the front side of the storage drawer and allows the drawer to easily slide in and o...

$8.93

Front Drawer Glide

The front storage drawer glide on your range is mounted on the side of the cabinet. The purpose of the drawer glide is to support the storage drawer from the front. If your front storage drawer glide is damaged or missing, or your storage drawer does not close properly, you should consider replacing the drawer glide. This product is sold individually. This part is approximately 2 inches in length, and 1 inch in width. The front drawer glide is made of white plastic. Many of our customers have rated this repair as easy. The storage drawer also uses a rear drawer glide, which you can find by searching part 977753.

$8.35

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, ...

$6.78

Igniter/Orifice Mounting Screw

$5.35

Steel Washer

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter ...

$96.24

Bake Igniter

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bought a new gas oven that did not come with a propane conversion kit.

  • Customer: Denny from Bishop, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 112 of 160 people found this instruction helpful
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. ... read more

Stove was set up for natural gas and needed to be converted to LP

  • Customer: Ed from Orange, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 113 of 182 people found this instruction helpful
The LP conversion kit contained very good, detailed instructions. I replaced the gas orifices, took off the bottom door and adjusted the regulator.

Used the screwdriver to adjust the low flame and everything was done. read more

Oven light receptacle broken - bulb base broke off

  • Customer: Paul from Spokane Valley, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 39 of 51 people found this instruction helpful
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snap... read more