WWGF3002KWB Westinghouse Range - Instructions

Replaced uper orifice n adjusted oven as instructed.

Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.

I removed the screws holding the door together,removed the broken panel and replaced it with the new glass
The part fit correctly and the re-assembly was easy.

I removed the four phillips screws to seperate the oven door sections (that lets the door handle drop off too.) and then took out four hex head screws that hold the glass bracket in place. I had to lift out the front glass to reach the broken back glass. After that, I just slipped the new glass into position and reversed the procedure. It took about 25 minutes. It took just about 25 minutes counting the time it took me to find a hex head nut driver. I'm willing to bet it saved me a bundle, too.

All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.

Followed your video and it was not hard at all

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

Open the door and slide in the new rack.

The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.

replaced it

I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

my dad and i did it together and it was easy. just had to remove the screws on the outside oven door pull the door apart, remove the old glass and put in the new and put the screws back in. hardest part was to get some of the screws out because they had been in so long.