Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWEF3006KWB > Instructions

WWEF3006KWB Westinghouse Range - Instructions

All installation instructions for WWEF3006KWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWEF3006KWB
31-45 of 709
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Large burner would turn on high and not cycle off

  • Customer: Kevin from Nashville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

trouble code F10 low oven temperature, oven not overheating,low resistance reading on ohm meter

  • Customer: Michael J from STATEN ISLAND, NY
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
Turned off electric,removed rear panel and replaced part.oven is now operating good as new.

Bake element burned in 2 pieces.

  • Customer: Mary from Cabot, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Easy repair. Removed 2 screws and connectors, replaced . (Just a Note) Stove has been a lemon since purchased. Only 3 years old and have already had to replace timer, burners, oven door hinges, and oven lower burner. I'd have been better-off buying a good quality appliance in the first place. Have had many problems and finally replaced 3 year old Frigidaire refrigerator. Same quality issues. Replaced dispenser circuit, defrost circuit, then compressor. Lost a fridge full of food 2x. Under warranty but a real hassle. I will never buy another Frigidaire product.

Oven would not heat, broiler still worked.

  • Customer: Eric from Lafayette, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 8 people found this instruction helpful
I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

Bottom elerment burnt into

  • Customer: Danny from Gaffney, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 9 people found this instruction helpful
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Large burner wouldn't heat

  • Customer: Phyllis from Elberon, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 30 people found this instruction helpful
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

the bottom oven element shorted and melted

  • Customer: angela from lake placid, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

broil element was bad.

  • Customer: William from Fort Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 7 people found this instruction helpful
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Needed an extra rack to bake more bread

  • Customer: Albert from Havertown, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 17 people found this instruction helpful
I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.

the indicator light for burners broke and shorted agaist the back panel on range

  • Customer: James from Caldwell, ID
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 12 people found this instruction helpful
This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson

Range would start beeping and needed to be unplugged.

  • Customer: George from TURNERSVILLE, NJ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

switch had a diffirent lug configuration

  • Customer: Robert from Andrews, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 16 people found this instruction helpful
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

Oven light stayed on & smelled like electrical burning.

  • Customer: Vincent from Brunswick, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 25 people found this instruction helpful
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Electric burner switch shorted out.

  • Customer: Armando G from Alice, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

broken lens over oven light

  • Customer: Leslie from Warsaw, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 20 people found this instruction helpful
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
All Instructions for the WWEF3006KWB
31-45 of 709