WWEF3000LWA Westinghouse Range - Instructions

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

I first unplugged the stove (which was the hardest part), I then set a bright light so I could see near the back of the oven. I then started the task of removing the old element by using a quarter inch nut driver, not to difficult at all. Once I removed the bracket I pulled it out far enough so I could disconnect the wires that were connected to the element. I had a bit of a hard time with one but after a little wiggling I got it loose. I was then able to remove the old element from the oven. I began the replacement of the new one, EASY ! I placed it in the oven, attached the electrical connection to the new element (made sure they snap in tight) and then replaced the bracket that held the element /coil to the back of the oven using the nut driver. All finished in about 15-20 minutes. I am not a strong woman , but a determined one. This fixed the problem and I am now baking like I have a new stove. The surface element is nothing to change , just unplug the old one and plug in the new one (simple). I use my front burner so much that it had began to smoke from so much food dropping and cleaning it over the years. MY main issue was the Bake Element and I really like my range and thought I would try this before buying a new range and I did it myself ! If I can do this anyone can believe me I am NO repair person, but this was very easy to do.

Ordered new racks and replaced them.

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.

i at first had a hard time finding the model # on this older electric stove. i did a chat with a rep from partselect.com and they sent me a web site that showed me where to look for it. that helped a lot. found it and searched on partselect.com . they had just what was needed. the purchase was easy and shipping was fast. i was worried it was going to be time consuming finding what i needed, not true once i found their web site. also, installation was easy.

Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.

Took screws out back of oven to get to connectors . Pulled old conectors off Installed new element took about 5 min. Very easy job. Also good time to clean oven .

purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Just placed the chrome bowl trays in place and was good to go. They look very nice.

my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great