WVSR1060D0WW General Electric Washer - Instructions

drilled off top plate of agitator to gain access ot bolt, removed bolt, removed agitator, replaced coupler and new bolt, snapped in place new agitator.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and the tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!

Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would most likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.

First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.

First I removed the agitator with a belt. Then I removed the nut with a wrench. The Agitator coupli was smooth on the inside so I knew that was the problem. I got the new part, slid it into place. Tightened the new bolt and replaced the Agitator component with a quick push downwards. Easy!

Unplug the washer. Turn off water supply. Disconnect hoses and have a bucket to catch the water standing in the hoses. Unscrew the 4 screws on the top of the control panel (my model had torx head screws). Flip down the control panel. Unplug the triple water valve. Disconnect the hose clamp from the water valve. Unscrew the water valve using a 1/4" nut driver. Replace with the new valve in reverse order. If your washer is older I would recommend also purchasing the hose & water inlet (number 803 on the diagram) I was afraid that mine would crack when I removed it. It was a very easy repair and I am happy that I did not have to pay a repairman to fix thia problem.

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.

I loosened the four nuts holding the motor in place, slid the motor toward the tub to slacken the belt enoug to remove it, then replaced old belt with new belt, pulled motor back in place until belt was tight, then tightened the four nuts holding th emotor in place.

I followed the instructions provided by GE that were stored in the control section of the washer. Removing the hub nut was a huge pain. It took Liquid wrench, hammer, pipe wrench and patience to remove it. Other than that it was fairly easy. I didn't like the way the tub seal fit so I used some silicon gasket making material to help make sure the seal sealed good against the tub.

I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.

Finding the disassembly instructions in the control panel was very useful. After disassembly and inspection obviously the transmission had lost oil and deteriorate the belt and actually threw it off. Finding your web site was very helpful. The exploded views parts catalog were great! We had it rush shipped. It was great to speak with a representative on a sunday was excellent. The rep was knowledgeable and we concurred on which part were needed. Tracking number was correct via e-mail but only rec'd tracking number for one of the two packages which was stressful at the fedex office at pick-up. All items were rec'd on time assembly was straight forward. The basin retainer nut came loose after 5 loads and made a terrible noise. I applied blue loctite to nut and reinstalled. Seems to be working correctly. Bought an extended warranty which added 4 yrs. Washer failed 2 months after warr. Expired. Figures!! Great experience with partselect thank you.

Unplugged washer. Removed four screws on the top panel, unplugged and removed old water level pressure switch (which was visually broken), replaced with new part, put the top panel back on, re-connected power, and tested to make sure that the washer would now fill to Extra-Large. Worked!

I used a pair of needle nose pliers and a screw drive to remove the clip holding the knob on its shaft. The new knob came with its clip already in place, so it "popped" right on. I ordered the compression ring in error and it it was not needed