WRT779RWYB00 Whirlpool Refrigerator - Instructions

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plugged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM

Just like the video. Hardest part was finding the right tool to unscrew the 3 screws which were easy. The rest was a piece of cake. I didn't replace the wire because I wasn't sure how to disconnect it from the fridge. The wire connections didn't look the same at the fridge wall as in the video.

Plan simple just screwed the screws out take the ice make out put the new one in and wait till the timer was ready and water went in and ice was made like brand new.

first remove ice maker 1-screw on the bottom all the way out and two screws on the top half way out slide up and out and unplug wiring as you remove then remove back panel unplug ground wire remove screws that hold fan assembly unplug wiring remove pressed on fan blade put new motor in reasemble and it was good to go

Your online video made our icemaker replacement a breeze -- saved a bunch of money! Thank you PartSelect!

I recieved the part from part select right away. While I was ordering I noticed a video I could watch on how to make the ice maker replacement part work. I was very pleased and the repair was a snap. Thanks alot for the help and the prompt service.

followed instructions provided. real easy. also installed new filter. forgot to flush the filter.

It was not the icemaker, instead it was the water inlet valve. I had ice in one hour. The biggest problem was getting the refrigerator from against the wall.

Loosen two top screws and removed one bottom screw and unplugged the old ice maker. Installed old arm on the new ice maker and plugged in new ice maker to the existing plugs and reinstalled new ice maker. Dumped ice in about one and a half hours. Full bin within 72 hours. Super easy.

Shut off power,(breaker box), removed the ice container, this had the crusher, makes it easey to remove the timer assy, loosened up the upper hex head screws, removed the lower phillips screw. Dis-connect the feed wire assy. I elected to dis-connect first at the timer unit. Remove the timer cover, then access to the wire connecter,remove the heater unit on the side of the of water pan. Drop the unit out and if necessary change the wire loom at back of refrig-, install new loom if necessary, reverse process on ice unit. Took about 45 minutes +-, marked the timer dial, see if I got rotation, etc. There is ports on the face of the timer to check voltage's. Now will install new water valve , and water filter to make sure all is back to normal. Made ice on start up, excellent service, parts are great, with necessary information. Thanks, bill.

Thought it would be difficult to replace and expensive. Very easy after all.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

Turn off water supply. Remove cardboard cover. Loosen metal supply line. Remove valve from edge of refrigerator. Remove electric connection, plastic water line and main supply line. Install new valve in reverse order... check for leaks.