Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRT21S4AW3 > Instructions

WRT21S4AW3 Westinghouse Refrigerator - Instructions

All installation instructions for WRT21S4AW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRT21S4AW3
136-150 of 393
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

frezzer iceing over and not cooling the refrigerator

  • Customer: Marcus from Pine Hill, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

the refrigerator door shelf retainer bar cracked due to overstocking the shelf

  • Customer: windy from chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
popped the shelves back into the interlocking socket.

broken glass shelf

  • Customer: Felicity from Baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I opened the fridge, put the glass in the shelf, and closed the fridge. Very easy.

Freezer built ice, fridge not cold enough and running constantly.

  • Customer: LUIS from CENTENNIAL, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

coil Iceing up

  • Customer: Thomas from Stuart, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

Light switch prevented door from closing.

  • Customer: Patrick from Penryn, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 5 people found this instruction helpful
The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

Broken bar and seal

  • Customer: Mark from Sandwich, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Snapped in the bars and with the seal once on the track went right on

2 of the 3 door racks were broken

  • Customer: KAREN from HOUSTON, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
It was extremely easy. All you had to do was to pop them into place.

Retainer bar on door snapped

  • Customer: Joe from Woodbridge, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
It's a pressure fit. Squeeze the ends and snap it in.

the refrigerator door was hard to close, and upon inspection I finally decided that the light switch was making the door hard to close.

  • Customer: Paul from Springfield, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

Bracket for door shelf broke

  • Customer: Mark from Woodbridge, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Ordered new bracket

the compressor capacitor overheated

  • Customer: Bart from goldsboro, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

both ref&frez were hot

  • Customer: Gary from Dunnellon, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.

Needed new drawer for refrigerator to replace broken one.

  • Customer: Nancy from Bellerose Manor, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I broke my drawer on a holiday Monday and Tuesday morning I had the new one in. your party was an exact match, even though the description said it might not be.

freezer was freezing and no refrigerator

  • Customer: Michael E from Uniontown, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instruction vedeo from partselect. THANKS!!!!!
All Instructions for the WRT21S4AW3
136-150 of 393