Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRT1G3EW0 > Instructions

WRT1G3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRT1G3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRT1G3EW0
211-225 of 447
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drawer slide broke due to overloading

  • Customer: Charles from Harvey Cedars, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
installed new slide support. No Problem. I would also like to compliment your service personnei on their prompt response. I believe I received the part within three days after ordering. Thank you

freezer frosted up and air could not circulate to the food section, causing the temperature to get warm, 55 degrees

  • Customer: PAUL from WEIRTON, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

Refrigerator warm, but freezer slightly cold

  • Customer: RONALD from LONG BEACH, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

broken glass shelf

  • Customer: David from Los Angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I Ordered the shelf and placed it in the fridge. The process was so easy and convenient, and the replacement part came early and I found myself wishing everything was this easy...

Broken crisper drawer slides

  • Customer: John from Amesbury, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I lifted out the old crisper pan cover and inserted the new one.

BROKEN door gasket

  • Customer: Ronald from West Springfield, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
i read on line that it is easier to install the door gasket if you remove the door which also involves taking the freezer door off. start at the top and work your way down. easier with two people but one person can do it.not difficult, just press the gasket into the groove and the closing of the door will adjust it as is is needed.knowing this sequence will save you time.

Freezer was cold bit the refrigerator was warm.

  • Customer: Christopher from Wilmington, DE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based on the diagnosis on this site I thought the 66% odds of the problem being the Defrost Timer looked pretty good, $30 including shipping versus a Sears tech phone estimate of $250-300. BINGO! Just follow the online installation instructions and don't forget to use the reset switch as described. Works like new! THANK YOU

The bottom shelf on the refrigerator door broke

  • Customer: Wendy from Caledonia, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My part arrived 2 days after I ordered it!!! Great service!!! The old one popped right off and the new one popped right on. Easy fix no tools required!!!!!

Refrigerator section warm

  • Customer: Laurie from Meridian, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!

Broken pan cover glass

  • Customer: Kathryn from BUCKEYE, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Part arrived...took it out of the package....put it right in the fridge. Perfect fit.....thank you so much.

fridge not blowing cold

  • Customer: wayne from marietta, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
bottom left cornerof fridge defrost timer replaced two bolts and a wire

broken

  • Customer: Mark from Laconia, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just replaced it

The gasket was torn and missing some chunks in some areas.

  • Customer: Jessica from Canton, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I did not believe the other posts about how easy this was because that is not at all how any project goes for me. I was wrong. The original gasket slid out of the lip around the door and the new one went back on in less than 5 minutes. It has made a HUGE difference in the performance of the fridge. It did take 2 or 3 days for the gasket to fully conform to the fridge itself, but there was still a good seal during that time.

2 door shelf retainers missing when bought refrig used.

  • Customer: Georgia from Bonners Ferry, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped retainers into place with no tools. Took less than a minute.

Broken right rail to dràwer.

  • Customer: Gregory from Circle Pines, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The part came right away, It only took me a couple of minute's to fix. I just flipped the shelf around. Slid one end of the rail in a slot, and put one screw in on the other end. Finished.
All Instructions for the WRT1G3EW0
211-225 of 447