Models > WRS6R3EWA > Instructions

WRS6R3EWA Crosley Refrigerator - Instructions

All Instructions for the WRS6R3EWA
76 - 90 of 901
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
2 broken shelving supports
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
Parts Used:
Crisper Cover Support - Front Crisper Support - Rear
  • Victor from Wilton, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
just quit working
Bought a new
capacitor.
Parts Used:
Run Capacitor
  • Denise from Lowell, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
18 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Parts Used:
Refrigerator Water Inlet Valve
  • Paul from Anderson, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
Parts Used:
Defrost Thermostat Kit
  • Albert from Buffalo Grove, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
22 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not cooling
Just took out 4-5 screws and follow the instructions and repair went great
Parts Used:
Damper Assembly - 115V 60Hz
  • Tony from LAURENS, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrig door would not close automatically
Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.
Parts Used:
Hinge Bearing
  • Michael from Lithia, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
14 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
Followed the steps in the video on your site, really easy to do.
Parts Used:
Refrigerator Ice Maker Assembly
  • Steve from ORANGE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
16 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
Parts Used:
Refrigerator Water Inlet Valve
  • Jim from Herington, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut properly
Removed the door and installed ne bushing on bottom of hinge
Parts Used:
Door Closing Cam Hinge Bearing
  • Matthew from Parker, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper Supports broken
Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.
Parts Used:
Crisper Support - Rear
  • GEORGE from ASHEVILLE, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
evaporator coil would freeze up solid. no air flow through coil; no cooling.
-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.
Parts Used:
Defrost Thermostat Kit
  • KEVIN from BRONX, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
18 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original gate broke at the swivel point
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
Parts Used:
Dispenser Crusher Housing
  • Charles from New Orleans, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
15 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker Doesn't Make Ice
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.
Parts Used:
Refrigerator Water Inlet Valve
  • JANET from NEW FAIRFIELD, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
19 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked gasket
Took off old gasket and pressed in new one. Took about 5 minutes for both procedures. Vey Easy!
Parts Used:
Fresh Food Door Gasket - White
  • Joel from Kissimmee, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was not cooling
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!
Parts Used:
Run Capacitor
  • Vicki from Johnson City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
16 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WRS6R3EWA
76 - 90 of 901