WRS26MZRHW1 Westinghouse Refrigerator - Instructions

THERMOSTAT--First I removed the fours crews that hold the back of freezer (inside freezer) in place. I then pulled the thermostat out about 3 inches and disconnected the two wires. Plugged in the new one and put back in place. Replaced freezer back and installed the four screws that holds it in.(iIf your freezer has a ice maker just loosen the 2 screws that hold it and lift the ice maker up off the screws
DEFROST TIMER--- removed one screw inside fridge by light bulb that holds in the timer and setting knob, then took out the two screws that held in the timer unplugged the old timer and replaced with the new one put back in the two screws that holds the timer in then replaced the one screw that holds the unit in place

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

Pulled the old ice container assembly out and discarded it and inserted the new one. It immediately worked and now dispenses both crushed and cubed ice through the door.

At top of refrigerator compartment, took out screws to cover (where temp control is) and to the right took out 2 screws to remove defrost timer and installed in reverse order. In freezer compartment, unscrewed back of freezer wall and took off completely. Removed old freezer thermostat, the body of freezer thermostat snapped onto coil and wire plugged in. Let run for 24 hrs, then made adjustments to temps, so far temps are back in normal range.

I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.

Kenmore Refrigerator

Turned off the water in the house because no dedicated valve to the refrigerator. Turned on the kitchen sink water to bleed off the water pressure.

Pulled refrigerator from wall and vacuumed up all the dust bunnies and cherrios for a clean work area.

Unplugged refrigerator.

Removed 4 screws that held on the rear cardboard panel.

Used 1/2" box end wrench to remove the water supply line form the valve and drained excess water into a bucket. Removed 2 more standard head screws from valve mounting bracket and pulled the valve unit out.

Detached the ice maker and water dispenser feed lines.

Labeled the 2 electric terminals (one purple and one green) and then disconnected them from the valve.

Installed new valve- had to cut a little piece off of water dispenser line from the valve because the new valve mounted without a nut on the end of it. (after market valve initially sent to me was incorrect due to web site error - but later got the correct one)

The after market valve has a different color on the solenoids (like an electric gate that allows water to go through on command). Despite the different color, the electric harness will only match up one way because the terminals are larger on one side.

The installation was fast and easy, however my icemaker is still not working.

I am guessing there is something wrong with the electrical somewhere else but replacing the valve probably fixes this problem most of the time

The plastic slides on the Upper and Lower Drawers were broken from years of abuse sliding the drawers in and out. The replacement of the plastic drawers required removing the glass front pieces using a screwdriver and gently seperating the plastic drawer from the front panel from under the assembly. The front panel easily slide out within the drawer runners. Simply slide the front on the new drawer and insert back into the refrig. That simple.

pulled tank out and cut two plastic lines

remove all freezer items and remove back panel covering the coils - about 8-10 nuts using a nut driver. The coils in my refridgerator were covered with a heavy frost - thermostat was also frozen over. Manually turn the defrost timer so the fan turns off to observe if the heating element is working (defrost timer is on the bottom front of the refrigerator on the left side). My heating element did work so I decided to replace the thermostat and defrost timer. Unplug the refrigerator. Disconnect 2 wires connecting the thermostat and unhook. Replacing with new thermostat - red and white wires that have male/female connectors and hook onto coil as before. Note that two parts with similar names were offered by PartsSelect and you really couldn't tell which was the right one - I got both but returning the unused one was very easy but cost a couple of bucks in shipping. Next, take out two screws and the bracket that holds the defrost timer in place and unplug it. Plug in the new one and screw it back in. Reinstall the back panel - throw out all that stuff in the freezer that you've had in there for 10 years and turn it back on - very simple and it worked perfectly. Very good experience with returning parts - excellent customer service.

Used exploded parts view to locate part. Removed old part and replaced with new defrost timer. Piece of cake.