WRS26MF5ASM Crosley Refrigerator - Instructions

swap filter

In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

The new bins and I installed them in the door. Nice to have door space again.

Easy slide it back in place

Slip the old one off and replace the new one with just snapping it in place!

Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.

Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!

Unscrewd the top hinge cove and removed two bolts from the hinge, lifted door off of the bottom hinge and laid the whole door on the floor using a beach towel to protect it from scratches. Unbolted the bottom hinge plate, replaced it with the new one. Then pulled out the old hinge bearing and replaced with a new one. Installed the door back on the bottom hinge while the magnet on the door strip held it place and rebolted the the upper hinge and reinstalled the hinge cover. All done in less than 10 minutes. No more popping sounds when I open and close the door!

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Then the motor is removed from it's housing by removing 2 more screws. 1...2...3 and you're ready to reverse the procedure. I am not mechanically inclined and this was easy. Saved myself perhaps $120.00. Repair folks wanted mininum of $60.00 just to come out. Part and shipping cost me 33 bucks.OH, DON'T FORGET TO UNPLUG THE FRIDGE. :>)

If you think you probably can't do this, you're like me... but you just had to try because you needed the part anyway right? This really was quite simple, a lot easier than it sounds from the description and saved me probably $75 I'd have had to pay a tech to do it. Just unplug fridge, yank that water spill tray out, yes yank, it's a bit hard to do that if you've not done it before. After that remove the 3 phillips head screws you just gained access to. Lift panel frame up then out. Disconnect wire harness plug and set that frame aside. Take out next screws exposed to free the unit. Tilt unit out and remove the two little screws and shims holding actuator in place. Remove broken one. Put new one in. Reverse all actions taken thus far. Plug fridge back in and have a drink of water like nothing ever happened. : ) You can do this!

First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it.

The only difficult aspect of the job was getting the old shelf support stud removed from the refrigerator wall - the support was broken off too short to allow vise grips to hold it. I had to use two screwdrivers to get under and then pop out the stud to the point I could get the pliers to hold. Everything eles pretty much just "fell together" very easily.

removed screws,removed broken parts and installed new parts.