WPRE6100G0WT General Electric Washer - Instructions

Just traded out the hoses and installed washer and started washing. Also got the replacement hose in a very timely manner, in turn only without washer for 5 days total. Thank You

removed screws from control panel. pulled panel back to reach control valve and removed two screws holding valve. found that freezing caused one valve to leak. pushed valve back and reinstalled. That did not work so ordered a new valve, installed it and all worked find. don't forget to unplug washer from electricity and turn off water supply. Also the garage
floor needs water spill removed asap as the water froze on me and made it difficult to remove.

remove screws from bottom of washer to remove the bottom of the washer so you can access the pump and motor assy. and remove two hose clamps.

"Thought" the belt was the problem - ordered new belt - waited for belt to arrive - opened washer. Belt was in perfect condition - problem is the clutch. Next time husband will verify problem before ordering parts.

Changed the dual water inlet valve.

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

New dual water inlet valve.

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

removed top and replaced .

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

Step one: Order the Belt and the $10.00 tool that fits on the motor sprocket to keep the belt from slipping off. Step 2: Lean the washer back at about a 45 degree angle, you may have to disconnect the water lines to achieve this. This puts the machine in a good position when you sit in front of it as you are installing the belt. Step 3: Install the tool over the motor sprocket leaving the grooves exposed. The belt fits in these grooves. Step 4: Slip the belt over the motor sprocket first and than the large sprocket wheel behind. This will take a little muscle as the belt is considerably smaller. After a couple of attempts at rotating the big sprocket the belt kept slipping off. I than took a plastic tie and strapped it around the belt and the big sprocket wheel, this kept the belt from slipping off as I rotated the wheel. Once the belt is on snip off the plastic tie and you are home free.

After figuring out to use a very small flathead screwdriver to get out the "star" screws holding on the front panel, since I don't have the proper tool for this, it was easy! Just disconnected hose lines from back of washer, unplugged the old valve, removed the screws holding it in. I disconnected the small water line that was connected to valve. I put in the new valve, reconnected everything, put panels back on, and it worked like new again.

I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!

Replaced dual inlet valve. Problem solved