WM3001HPA (APTEEUS) LG Washer - Instructions

Watched instructional video. Made it easy

Honestly youtube but pretty simple install.

I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

you tube it , not to hard to install

Watch the video to repair and follow along

bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour

removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

I unplugged the washer shut off the water and disconnected the hoses. Then removed the top lid and removed old valves and installed new ones. Very easy plug and play installation.

Had to manually shut off water valve behind the washing machine to stop the filling process. Followed repair video from the website.

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 seconds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

remove 2 screws from top panel - pull top panel back and lift off washer. reach down on front side and remove wire harness that is attached to door lock assembly. remove the 2 screws on front of door lock,remove and replace with new assembly. attach wire harness and then tighten assembly with the 2 screws. replace top of washer panel and tighten with 2 screws.

Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!

Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and gasket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.