WLW1500RBL Hotpoint Washer - Instructions

After removing the rear cover I removed all the hose connections as this gives a better access to the mounting screws. Next disconnect the drive coupling. Remove the 2 inner mount screws frist then remove the 3rd screw.
Reversing this procedure makes mounting the new pump easy. Also I went to GE's web site and downloaded the parts sheet that also gave me the number for the proper pump.
E. Renico

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

I was pleased with how quickly my part arrived and that it was still in stock as the washer was quite old. I had to remove screws on back panel to get at part. only a couple of screws held the part in place and 4 wires were connected. The hardest part was pulling the part out of black hose that connected water into machine. It had been on so long it wouldn't pull out and part of it broke off in hose. It took some fussing to get it out and then the new part connected easily.I took one wire off at a time and put on new part as to not get them mixed up.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

Tilted the washing machine, removed 4 hoses from the pump and the drive connector;
removed 3 nuts that hold the pump; install
the new pump and put back the hoses; to be safe, I unplugged the electric

I unhooked the fill lines from the washer. I unscrewed the cover plate of the water inlet valve, and pulled the valve out enough to disconnect the fill hose. I unscrewed the band clamp on the fill hose and disconnected the hose.

I took the replacement part and one by one moved the four wires from the old part to the new part to make sure I connected each to the proper terminal. I then reattached the fill hose and clamped it. (This was the only "hard" part since the hose has little length to work with and is inside the machine.)

After attaching the all the internal connections. I took the coverplate from the old valve and screwed it to the new valve. I screwed it all back in place. Before reconnecting the fill lines from the wall, I replaced the rubber washers in the hose (a good practice to do when re-connecting these hoses). Connected the fill lines, and voila--working washer!

Very easy and intuitive repair.

I removed the four hoses that were connected to it, then I removed the three screws holding the pump in place. Then I removed the drive adapter that was connecting the pump to the motor. I then did everything in reverse order to install the new pump and everything worked just fine. Thanks!

After pulling the knob out ( on position) a white retainer clip was visible behind the knob. Using a paper clip bent in to a "J" shape I was able to easily remove the retainer clip and knob . The old knob had several stripped teeth that caused the problem. The new knob came with the retainer clip installed . The knob slipped on and locked in position.

Husband did it. Tipped machine onto its front. Took out some screws and disconnected a wire and removed hoses from pump. Then put it all back and it is as good as new. This is the second pump in two years, but it beats the price of a new machine.
Your service is excellent. Both times, I have ordered the part is here the next morning. Never have had such service from anywhere else. I am telling all my friends about your web site.

Unplug the machine. Turn it face down. Take the back off. Take the four hoses off the pump. Unscrew the screw holding the connection to the motor and carefully slide the brace off without bending it. Remove the 3 screws holding the pump on. Take the old pump out. Screw the 3 screws back on. Attach the drive mechanism with the clamp carefully being sure to even it out under the clamp as you tighten it. Reattach the hoses. One of my hoses leaked after wards so I had to trim a half inch off to get a better grab on the pump. Put the back on and stand her up. Plug it in and test her out.

remove enough screws in rear panel to access water inlet valve. remove two screws holding water inlet valve to washer frame and flex valve outward enough to remove clamp on water inlet tube. wiggle inlet tube off of valve inlet nipple and back valve out enough to see wires. after noting wiring color codes remove the four wires from the old valve and discard old valve. install the new valve simply by reversing entire process. only difficult part of entire process is removing and reinstalling the inlet tube on the valve body as the tube is short and limits room to work.

had to pull knob out to see the clip locking the knob to the post.
finally got the clip out, pulled knob off sand put on new knob with new clip

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.