WLW1500BBL Hotpoint Washer - Instructions

Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.

This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!

Trouble shooting on internet only mentioned worn drive belt as a cause for no spin. No mention of the possibility of a transmission problem burning out the centrifugal clutch. So the drive belt was ordered and when I checked tracking when it was late, I was informed that it was already delivered and signed for by some stranger, jmorris. Later that night I found the package at my door to late to do the repair that night. The next evening the repair was attempted and it was not difficult with the youtube video for guidance. Back together but it did not spin or agitate. On the third run dthrough the procedure I noticed that the clutch was really hot and the notor was not locked. But the big pully would not complete but bart of a revolution and hard stop. The repair was a failure and after the time spent diagnosing the wrong problem with inadiquate trouble shooting on the internet chart and the time ordering and waiting for the second chance delivery. The failed repair delayed to the point that the customer did not have time to do their laundry berore their weekend trip. They will have to get a new machine after waisting so mych time with a less than fully informed repair attempt. The internet trouble shooting help was inadequate. The delivery of the parts was botched using FedEx instead of UPS. At the last minute after hours of involvement it came to light that the machine was history and we were suckered into buying the wrong part and running out of time for the customer to ready their clothes for their trip. I felt so bad of the machine resisting the repair process thaqt I discounted my labor time and told the customer pay me what they felt would be ritght. It was not all part selectt's fault but they had their page in the story.

Pulled top off and removed corner mounting plate then unscrewed mixing valve.replace wiring to valve and mount new valve in it's place .put back support and corn brace .then attached hoses and put back in service .work great for 20 plus yr machine.thanks tom

removed 3 screws from the back. Then removed the little water line clamp. unplugged the 4 wires. took the new part. plugged it in. put on the water line clamp. put the 3 screws back on. put the hoses on the back again. turned on the water supply. and started washer.

I took the back cover off of the washer, studied my next move and jumped in.Easy Lou-eezee!

Did some checking to make sure the filter, screen and hose were unobstructed. Turned off water at faucets, disconnected hoses and drainage hose. Unplugged machine and pulled out far enough to access back. Used nutdriver to remove 6-7 screws that held the back on, and then inlet valve plate. Removed clamp on outlet hose, then one by one removed wires, making sure to connect them to the same connections on new valve. Re-connected outlet hose and reversed procedure. Easy fix. Went ahead and replaced hoses while I had it out.

Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!

Removed existing knob by using pliers to release clip from shaft. Inserted new knob (with clip attached) onto shaft and aligned with shaft groove to engage clip. Easy breezy.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

Since the valve sprayed water out in one particular spot, it was easy to determine what part I needed. After I received the part from "Part Select" it was super easy to replace and took about 10 min. and the washer was good as new.

We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.

Unplugged washing machine from electrical outlet. Turned off water supply to washing machine. Removed inlet hoses. Removed 2 screws to get panel off that water valve attaches to. Removed the panel for access to water valve. Removed fill hose from water valve and then unbolted valve from panel. Made diagram of electrical wiring to ensure correct placement on new valve. Attached new water valve, electrical wires and fill hose to valve. Installed panel in machine and hooked up inlet hoses. Turned on water supply and inspected for leaks. Turned on washing machine to verify filling and repair was OK.

Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You

Very straight forward install. First removed the agitator itself by pulling straight up on it. Then removed the agitator coupling without the need of any tools just pull it straight off. Install new coupler and agitator.