Parts That Fix General Electric Washer WHRE5550K2WW Will not drain
Will not drain is a commonly reported symptom for the WHRE5550K2WW General Electric Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WHRE5550K2WW General Electric Washer that will fix Will not drain. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
Replacing your General Electric Washer Drain Pump and Motor Assembly
Customer Repair Stories
washer didn't spin & water would not pump out
-
Ken from West Monroe, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Wrench set
machine would not drain all other functions seemed o.k
-
douglas from danby, VT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access the hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.
Replacing your General Electric Washer Drain Hose
Customer Repair Stories
Hose would not seal at rear of washer.
-
Charles Wayne from Forest Hill, WV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
Purchased used washin machine w/o drain hose
-
Daniel from Oxford, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
Replacing your General Electric Washer 6-Rib Drive Belt
Customer Repair Stories
Broken belt.
-
Mike from Meridian, ID
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
broken drive belt
-
jon from barry, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
This lid switch with wire harnesses is used in washing machines. The pin on the lid switch pushes onto the lever of the switch to communicate to the machine that the washer lid is closed. If your washing machine is not running when the lid is closed, not spinning, draining, or agitating, replacing the lid switch could solve the problem. The tools needed for this repair are: putty knife, 1/4 inch nut driver, wire strippers and crimpers. Refer to the manual for further installation instructions. Remember to unplug your washer from the power source as a safety precaution.
Replacing your General Electric Washer Lid Switch with Wire Harness
Customer Repair Stories
Washer didn't wash/spin
-
Eva from NAPLES, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
washing machine would not go through all cycles or agitate
-
Brian from Millerplace, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins