Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WHDSR209DAWW > Instructions

WHDSR209DAWW General Electric Washer - Instructions

All installation instructions for WHDSR209DAWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WHDSR209DAWW
331-345 of 455
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

had a pin hole in the drain pipe

  • Customer: ROBERT from Bynum, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.

it was leaking

  • Customer: Beverly from Casper, WY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.

No cold water coming in

  • Customer: Maurice from Port St.Lucie, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Viewed the hot/cold valve. I saw that the cold water solinoid was burned. Ordered new valve and replace old valve. On my washer 4 screws held the switch panel, easy to remove and gave me plenty of room to veiw and do the repair.

water pump died

  • Customer: Richard from Mansfield, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Was easy. Removed pump, ordered yours and replaced

control knob's inner teeth were ground down and wouldn't adjust timer knob

  • Customer: james from fairfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered both control knob ($6.46) and timer knob ($22.61).I didn't need/use the timer knob, so I returned it. I switched out the control knob by removing plastic pin and replaced w/ new control knob & pin. My 3-yr old grandson sat on the dryer and held the flashlight. I certainly saved mucho by not calling "repair-man"..Total repair was $6.46 + S & H.Now, if we can just keep this baby (family of 6)going til it's time to downsize.

leaking

  • Customer: Nicolas from Palisades Park, NJ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
As directed by the book.

Leaking water on final pump out

  • Customer: Francis from Rochester, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

Washer would not drain or Spin!

  • Customer: Danny from Clarksdale, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

leaking drain line

  • Customer: frederick from CHARLOTTE, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took screw driver unscrew the srews remove the drain hole stuck the new hole in it,s place and replace with new srews that was it.

Agitator did not move

  • Customer: David from Albion, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
With the instructions found online, this was a quick easy repair. I used youtube to have video to show the method. Used rope to pull up agitator, used wrench to loosen bolt and then put back together. Part was delivered really fast, I recommend Partselect.com for the parts you need!

broken dampening straps

  • Customer: kenneth from mazeppa, MN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4

Bought the unit used and noticed when i opened the front of the washer indications of the pump leaking and some rust on the pump/motor bracket.

  • Customer: james from baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

Water drip into washing well

  • Customer: Scott from Jupiter, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Unplugged washer. Shutoff water supplies. Removed control panel. Disconnected wiring to valve. Removed hoses from old valve. Removed valve mounting screws (x2). Installed new valve and secured with mounting screws. Replaced washers in supply hoses and reconnected hoses. Reconnected control wires. Turned on water supplies. Plugged washer into electric outlet. Tested. EVERYTHING WORKING SO FAR!!!

beyond belief!!

  • Customer: Hilda from harpswell, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After ordering the part on a Friday afternoon, I was amazed to have it delivered before 2PM the next day. The part was the timer knob and it was a perfect fit. It took less than 15 minutes to replace the faulty knob with the brand new one. Amazing!!!

water leak at drain hose extension

  • Customer: WILLIAM from HAMPTON, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the drain hose clip and pulled the old broken drain hose extension out at base of washer rear... pushed the new drain hose extension into washer and screwed the new drain hose clip inot place two screws... very simple very easy very fast... problem solved
All Instructions for the WHDSR209DAWW
331-345 of 455