Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WGD9600SU0 > Parts

WGD9600SU0 Whirlpool Dryer - Parts

All parts for the Whirlpool Dryer WGD9600SU0

Below is a list of all parts for the Whirlpool Dryer WGD9600SU0 - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the WGD9600SU0
1-14 of 186
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer do...

$21.73

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

$26.37

Lint Filter

This filter collects lint as it passes through the dryer vent.

$20.42

Idler Pulley

The idler pulley with tri-ring and gasket, also known as a dryer belt tension pulley wheel, is used in dryers. This part maintains the right amount of tension for the belt to rotate the drum. This effectively spins the drum. If your dryer is experiencing any of the following symptoms, it is best to replace this part: not rotating, does not start, making squealing noises when it is in use, or it does not tumble properly. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions.

$42.43

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$13.09

Drive Belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

$10.34

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this pa...

$17.97

Igniter Kit

If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-inch flat igniter, bracket, 4-inch wire leads, and the plug. The kit can replace both round and flat igniters and is used for many gas clothes dryers. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is located within the burner assembly, so you will require tools to complete the repair. You will need a putty knife, a small flat blade screwdriver, a 5/16 nut driver and a 5/16 socket with a ratchet.

$21.40

Thermostat, Internal-Bias

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

$9.74

Light Bulb - 10W

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

All Parts for the WGD9600SU0
1-14 of 186