Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WFW9150WW00 > Instructions

WFW9150WW00 Whirlpool Washer - Instructions

All installation instructions for WFW9150WW00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WFW9150WW00
31-45 of 118
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F21 Error - Water in washer not draining.

  • Customer: Christopher from GLENDALE, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

The washer drain pump had to be replaced.

  • Customer: John from ARMINGTON, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

replace the pump motor

  • Customer: Jay from MALVERN, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
First tilt the washer back so you can drain water from the lines to the pump and the pump itself. Disconnect the lines with a pair of pliers and use a screwdriver to move the rubber stopper so that the pump will move to the right. With pump now in position to lift up and out of the washer , do it so you can disconnect the wire assembly. Replace the pump starting with the wires, then slide it in place and secure it with the rubber stopper. Attach the lines and make sure they are well sitted and clamped. set on feet and you are ready to wash.

Washer would not drain flashing f-21 code

  • Customer: Casey from REXBURG, ID
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 1 of 1 people found this instruction helpful
Took it old pump and replaced with new pump VERY EASY

Counter weight flew apart

  • Customer: Mark from BENTON, AR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 1 of 1 people found this instruction helpful
Three 1/2 bolts tighten as required

F 21 code kept appearing even though trap clean out was clear.

  • Customer: Michael from LUCKEY, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced drain pump took longer to soak up water than actually replacing the pump motor with mine having the pedestal underneath I did not have to tip the washer at all so it was fast and easy. Three screws taking the front cover off a screwdriver lifting the Rubber and sliding the motor off and pair of pliers 4 to hose clamps making it a breeze.

It wouldn't drain anymore so I started looking on the internet for a solution. I came upon this website and found the part I needed. It was easy to install. It fixed the problem I had with the washer.

  • Customer: Ricardo from DETROIT, MI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I just took off the old part and installed the new one. The new part was a bit different.

Broken striker

  • Customer: KERRY from CLYDE, TX
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Remove two star screws. Remove broken striker. Installed new striker. Took two mins.

Washer belt stretched from years of use and walked off pulleys

  • Customer: Michael from PHOENIXVILLE, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I pulled the washer away from the wall to comfortably access the back panel. I then removed about a dozen 1/4 drive screws. I had to remove all the screws in the panel and the screws and cross brace directly behind the drum in order to install the new belt. Note: it will seem like the belt is too small when in reality it is perfect. There is no type of adjustments or tensioners that I found so you need to place the belt on the motor pulley correctly and then walk the belt on the drum pulley. Make sure the belt is lined up with the marks on the drum pulley that the original belt had left. You may need to attempt to walk the belt on 2 or 3 times before it finally goes on. If you have any mechanical knowledge you will find this to be a gravy job.

washer would'nt drain

  • Customer: RICHARD from SANTA CLARITA, CA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

Washer posting a f6 error

  • Customer: Robert from Salt Lick, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 29 of 91 people found this instruction helpful
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

F21 code

  • Customer: Mike from Columbus Grove, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

drain pump impellar busted

  • Customer: jeremiah from royalton, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Timer was not advanced due to door lock failure

  • Customer: EMMANUEL from CLINTON, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

The orignal bellow disinigrated so water leaked everywhere

  • Customer: Kelly from Irmo, SC
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Well first off the part is different then the orignal so it does not fit correctly. I removed the old bellow and its cicular spring clamps. On the new bellow there is not enough lip on the rubber for hte clamps to be put back on and hold the bellow in place so it still leaks out the door. if the part was a match it would work but since the part number was changed and the design was changed it now does not fit correctly. INstructions did not come withthe part so had to find them online.
All Instructions for the WFW9150WW00
31-45 of 118